Makita HR2641 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita HR2641 manuals!
Problems with Makita HR2641?
Ask a Question
Free Makita HR2641 manuals!
Problems with Makita HR2641?
Ask a Question
Makita HR2641 Videos
Makita HR2641 ?????? ????. ??????????? + ??????
Duration: 19:22
Total Views: 454
Duration: 19:22
Total Views: 454
Makita HR2641??????? ?????????? ?? ??????| ?????, ????????????, ??????????????
Duration: 1:56
Total Views: 3,319
Duration: 1:56
Total Views: 3,319
?????????? ??????????? Makita HR2641 / Unboxing Makita HR2641
Duration: 1:55
Total Views: 2,404
Duration: 1:55
Total Views: 2,404
?????????? SDS-plus MAKITA HR2641 800 ??, ???? ? ????????? ??????????? ? 220 ?????
Duration: :59
Total Views: 198
Duration: :59
Total Views: 198
Popular Makita HR2641 Manual Pages
HR2631F Instruction Manual - Page 2
.... ENGLISH (Original instructions)
SPECIFICATIONS
Model
Concrete
Core bit
Capacities
Diamond core bit (dry type)
Steel
Wood
No load speed (RPM)
Blows per minute
HR2631F HR2631FT HR2641 HR2630 HR2630T
26 mm...and development, the specifications herein are subject to change without notice. • Specifications may differ from heat, oil, sharp edges or moving parts. Failure to power ...
HR2631F Instruction Manual - Page 3
... repaired before making any other condition that cannot be controlled with these instructions to carry the current your power tool serviced by poorly maintained power tools.
22. Use the power tool, accessories and tool bits etc. Keep handles dry, clean and free from those intended could result in good condition. When using only identical replacement parts...
HR2631F Instruction Manual - Page 4
... NOT safety glasses. Be sure the bit is secured in this
instruction manual may be toxic. Check tightness of control... an electric shock.
4. Keep hands away from repeated use) replace strict adherence
to produce vibration.
Wear ear protectors. Wear a...with product
(gained from moving parts. 11. GEB007-7
ROTARY HAMMER SAFETY WARNINGS
1. Be sure no load. The bit could burn your skin. 14...
HR2631F Instruction Manual - Page 5
... stops may lower the illumination. • Do not use thinner or gasoline to stop. For Model HR2631F, HR2631FT, HR2630, HR2630T
CAUTION: • If the switch trigger can not be sure that the reversing switch is fully set to a complete stop the tool from the locked position, pull the switch trigger fully, then...
HR2631F Instruction Manual - Page 6
...of the quick change
drill chuck and set the line to ...drill chuck 3.
Use a twist drill bit or wood bit.
6 This tool has a reversing switch to the position (A side) for clockwise rotation or the position (B side) for SDSplus
2. Changing the quick change chuck for SDSplus
For Model HR2631FT, HR2630T
The quick change drill chuck. Rotation with
hammering
2. Removing the quick change chuck...
HR2631F Instruction Manual - Page 7
... limiter actuates, switch off and
unplugged before installing the bit.
1. Bit grease Coat the bit shank head beforehand with a small amount of the tool. • Bits such as hole saw, which tend to be sure that the protrusions on the tool. This chuck lubrication assures smooth action and longer service life.
Torque limiter
ASSEMBLY
CAUTION: • Always...
HR2631F Instruction Manual - Page 8
...sure that the bit is securely held in the figure.
1
1. After installing, always make sure that the bit is securely held in the figure and with its toothed side is convenient for drilling holes of uniform... allow the depth gauge to be locked.
8 Chuck cover
2
015255
To remove the bit, pull the chuck cover down all the way and pull the bit out. Toothed side of arrow shown in place ...
HR2631F Instruction Manual - Page 9
...shown in the figure. Install the dust cup (optional accessory) on the tool so that time, proceed as shown in the figure with the chuck cover pulled take it ...1
3
015351
Before installing the dust cup, remove the bit from falling over the tool
and on yourself when performing overhead drilling operations. Bit 2. Attachment
2
012896
NOTE: • When installing or removing the dust...
HR2631F Instruction Manual - Page 10
... becomes clogged with hammering" when the
quick change drill chuck may occur while operating the tool with no load. However, the tool may result in the loss of control of the tool and potentially severe injury.
015355
Set the action mode changing knob to your bit, decrease the tool performance and shorten the service life of...
HR2631F Instruction Manual - Page 11
...
Operate the tool with hammering" action, the diamond core bit may be damaged. Chuck key
1
015358
To install the bit, place it , refer to tighten the chuck. To remove the bit, turn the sleeve clockwise to "changing the quick change drill chuck as it will go . Change cover
1 2
1. Tighten the chuck by hand.
Sleeve
3. Spindle 2. For Model HR2631F, HR2641, HR2630
1. Change cover...
HR2631F Instruction Manual - Page 12
... specific legal rights, and you may also have been made or attempted by Makita Authorized or Factory Service ...trouble is caused by small metal dust or similar. • Empty the dust cup before removing a drill bit. • When using Makita replacement parts. Discoloration, deformation or cracks may differ from the date of original purchase. This Warranty does not apply where:
repairs...
HR2641 Parts Breakdown - Page 2
.... 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. Model HR2641 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
286288-8
002
455393-4
003
325813-1
004
346177-0
005
233916-6
006
233989-9
007
346834-0
008
122878-2
008 D10
009
346181-9
010...-7
050
210028-2
CAP 35 CHUCK COVER RING 21 GUIDE WASHER CONICAL COMP.
HR2641 Parts Breakdown - Page 3
...HOLDER GUIDE PIN 6 COUNTER WEIGHT TAPPING SCREW 4X60 BAFFLE PLATE FIELD 115V MOTOR HOUSING HR2641 NAME PLATE CLEAR LABEL CARBON BRUSH CB-407 (195007-0) BRUSH HOLDER TAPPING SCREW 4X35 HR2641 SERIAL... 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 0 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 2 PC. 1 1 PC. 1 1 1 1 SET 2 PC. 4 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 5 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 2 PC.
Makita HR2641 Reviews
We have not received any reviews for Makita yet.