Makita HB350 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita HB350 manuals!
Problems with Makita HB350?
Ask a Question
Free Makita HB350 manuals!
Problems with Makita HB350?
Ask a Question
Makita HB350 Videos
Makita HB350 Magnetic Drill
Duration: 4:49
Total Views: 291
Duration: 4:49
Total Views: 291
HB350 Makita Magnetic Drill 35mm
Duration: 4:49
Total Views: 1,676
Duration: 4:49
Total Views: 1,676
Máy Khoan T? Makita HB350/ Makita HB350 Magnetic Drill
Duration: 6:07
Total Views: 1,982
Duration: 6:07
Total Views: 1,982
Makita HB350 Magnetic Drill
Duration: 4:49
Total Views: 794
Duration: 4:49
Total Views: 794
Popular Makita HB350 Manual Pages
Instruction Manual - Page 1
FR Instruc�ons originales ES Originele instruc�es
HB350 Magne�c Drilling Machine
WARNING: For your new Magne�c Drilling Machine, please read this carefully BEFORE using .
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1 ORIGINAL INSTRUCTIONS
A GUIDE TO GOOD DRILLING PRACTICE
To get the best possible performance from your personal safety, READ and UNDERSTAND...
Instruction Manual - Page 2
... new Magnetic Drilling Machine, this guide contains simple, sensible pointers for municipal waste, operating in the equipment, used electrical and electronic equipment may have observed all the general and specific safety procedures. CONTENTS
• HB350 Functional Description • The Broach Cutting Concept • General Power Tool Safety Instructions • Optional Accessories •...
Instruction Manual - Page 3
...life of a machine is lower than for a traditional twist drill. you understand the concept. CUTTING TIME CUTTING TIME
EN
HB350 FUNCTIONAL DESCRIPTION
Cutter capacity - 1.3/8"
Chuck Capacity - ½"
No load speed
- 850 rpm
Power consumption - 1050w
Clamping..., these specifications are unfamiliar with the use of the hole, rather than converting the entire hole to read this...
Instruction Manual - Page 4
... installed...codes and ordinances. Remove adjus�ng keys or switches before plugging in place whilst the drill is an increased risk of flammable liquids, gases, or dust. EN
GENRAL POWER TOOL SAFETY INSTRUCTIONS...INSTRUCTIONS. Clu�ered benches and dark areas invite accidents. 2.Do not operate power tools in explosive atmospheres, such as in moving parts...cord. Replace damaged ...
Instruction Manual - Page 5
... foo�ng and balance at the rate for your model. Dust mask, non-skid safety shoes, hardhat, or ...support the workpiece to a stable pla�orm. Service 1.Tool service must be �er and safer at all �mes. Properly maintained tools, with the switch is designed.
3.Do not use only iden�cal replacement parts. Use safety equipment. Use of unauthorized parts...
Instruction Manual - Page 6
...you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
• HSS Cu�er • TCT Cu�... • A�er use or being transported the unit should be replaced immediately with MOLYCOTE grease. • When not in the slide but does...8226; Parts that the machine is remedied by adjus�ng the tension screws on...
Instruction Manual - Page 7
...edge and excessive heat generation.
• Slender and long shanked cutters are governed by rigidity of set and maintain a constant surface speed (RPM) for a given material and vary the feed rate within...
• Machine feed is measured in inches or millimeters per minute and is preferable to set up to rapid cutting-edge wear at high speeds. Heavy feeds on several factors including tensile ...
Instruction Manual - Page 9
... the machine supported before the magnet is clamped onto a vertical surface or in an inverted position. FITTING THE SAFETY GUARD
DRILL GUARD INSTRUCTIONS Ensure drill unit...replace the bolt through the fixing lug on the lower arbor bracket. When drilling, the guard should be in contact with the surface being drilled. As the drill is a push fit into the self-seal gland at a secure part...
Instruction Manual - Page 13
...
33 CARBON BRUSH WASHER
2 EBD031
34 CARBON BRUSH FIXING SCREW
2 EBD032
35 PG9 PUSH FIT GLAND
1
40025
36 MOTOR LOCATING KEY
1 M1019 Nr. Description
Qty Part No
1 CARBON BRUSH ASSY. 6.3X10X18
2 EBD002
2 BRUSH HOLDER ASSY.
2 EBD001
3 SCREW M4 X 12
2 EBD003
4 SPRING WASHER M4
2 EBD004
5 PHILIPS HEAD SELF-TAP SCREW 4.8X45
4 EBD005...
Instruction Manual - Page 15
...-50HZKJD17F-P2-F2-V3-M2-A1 37 MAGNET SWITCH - Description
Qty
Part No
1 CONDUIT (large dia 12mm) - PMA BVND-M160GT
1 40026...8 WARNING PLATE MAKITA HB350 CE JAPAN
M1002
CWEAJRANPIANNGMPALKAITTEAMHABK35IT0ACHEBJ3A5P0ACNE BELGIUM MBWEAALKGRINITUIANMHGBP3L5A0TECEMJAAKPIATNA HB350 CSA JAPAN
M1003 M1014
WARNING PLATE MAKITA HB350 UKCA UK
M1018
WARNING PLATE MAKITA HB350 RCM AUSTRALIA
M1021
...
Makita HB350 Reviews
We have not received any reviews for Makita yet.