Makita GFD02D Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita GFD02D manuals!
Problems with Makita GFD02D?
Ask a Question
Free Makita GFD02D manuals!
Problems with Makita GFD02D?
Ask a Question
Popular Makita GFD02D Manual Pages
DC40RA Instruction Manual - Page 2
... Always recycle battery. Defective battery.
Charging (80 - 100 %). SPECIFICATIONS
Model:
DC40RA
Input
A.C. 120 V 50-60 Hz / 50/60 ...Specifications may differ from country to country.
• The weight according to charge. Do not destroy battery by fire. Charging (0 - 80 %).
Charging (Cooling abnormality).
Do not expose battery to water or rain.
ENGLISH (Original instructions...
DC40RA Instruction Manual - Page 3
... tested and found to comply with the instructions, may cause harmful interference to operate the equipment. Increase the separation between the equipment and receiver.
- Do not charge battery cartridge when room temperature is damaged, ask Makita authorized service center to replace it will not occur in a particular installation. Do not plug or unplug the...
DC40RA Instruction Manual - Page 4
... is unplugged.
4 ENGLISH Never use it within another five seconds after this , the melody sound changes in blue color, charging may differ according to the guide of charge. (In selected silent mode, no completed charging signals comes out. (Silent Mode) 5. Changing melody upon completion of the charger can be opened with...
DC40RA Instruction Manual - Page 5
...lbs).
WARNING: Always be longer than usual in order to enable the battery to repair or maintenance, if the blue and red light flashes alternately so often.
The gross...Trouble on regular basis. Exhaust vent 2. Cooling system
This charger is equipped with cooling fan for heated battery in this manual, and complete the whole procedures at once. WARNING: Follow the steps instructed...
GFD02 Instruction Manual - Page 2
...• The weight may differ from heat, oil, sharp edges or moving parts.
Power tools create sparks which may not be available depending on the attachment(s), ...Power tool plugs must match the outlet. Keep work area clean and well lit. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
GFD02
Drilling capacities
Steel
13 mm (1/2")
Wood
Auger bit: 38 mm (1-1/2") Self-feed bit:...
GFD02 Instruction Manual - Page 3
... that cannot be caught in the instructions. avoid contact. Liquid ejected from moving parts may result in the off . However... tools and accessories. If contact accidentally occurs, flush with specifically designated battery packs. Stay alert, watch what you are ..., screws or other condition that have the power tool repaired before use common sense when operating a power tool. ...
GFD02 Instruction Manual - Page 4
...maintained.
2. Cordless driver drill safety warnings
WARNING...(gained from rotating parts.
5. Do not...replace strict adherence to pull it is severely damaged or is likely to bend if allowed to follow the safety rules stated in this instruction manual may result in personal injury.
2. Do not disassemble or tamper the battery cartridge. Service
1. Have your eyesight.
5. Never service...
GFD02 Instruction Manual - Page 5
... result in such a manner that it from the tool.
14. Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near....
Button 3. by Makita. SAVE THESE INSTRUCTIONS. Tips for the Makita tool and charger. Overcharging shortens the battery service life.
3. CAUTION: Always install the battery cartridge fully until it may cause...
GFD02 Instruction Manual - Page 6
...under one of use and the ambient temperature, the indication may have the tool serviced at a Makita service center. The tool will blink when the battery protection system works. In this ... after the switch trigger is released, have malfunctioned.
► 1 . Switch action
CAUTION: Before installing the battery cartridge into the tool, always check to see that causes it to the "OFF" ...
GFD02 Instruction Manual - Page 7
...change the speed, switch off the tool first.
CAUTION: When not operating the tool, always set to the correct position before operation. Depress the reversing switch lever from the A side for ... tool stops automatically and the lamp starts flashing. Reversing switch action
CAUTION: Always set the speed change lever is coming down extremely during the operation with the speed change...
GFD02 Instruction Manual - Page 8
...or a piece of the tool.
CAUTION: Use the hanging/mounting parts for temporarily hanging the tool. Place the driver bit/drill bit in the personal injury. NOTICE: When hanging the...Installing or removing driver bit/ drill bit
Installing hook
CAUTION: When installing the hook, always secure it will slip at various torque levels when set at marking. Sleeve 2. This can be installed...
GFD02 Instruction Manual - Page 9
... obtained with wood drills equipped with a guide screw.
Start the tool slowly and then increase the speed gradually. Recess 4. Drilling operation
First, turn the adjusting ring so that the arrow points to the proper torque level for your work. Driver bits 45 mm-long (1-3/4") can install the side grip either right or left...
GFD02 Instruction Manual - Page 10
...manual...set forth at below website for more details regarding these accessories, ask your local Makita Service Center. • Drill bits • Driver bits • Driver...setting the reversing switch to reverse rotation in order to be removed simply by Makita Authorized or Factory Service Centers, always using Makita replacement parts... SAFETY and RELIABILITY, repairs, any other accessories or...
GFD02 Parts Breakdown - Page 2
Model GFD02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
858D02-2
002...-1
021
191N20-0
021 C10 263005-3
021 C20 252126-6
021 C30 8026Y7-1
021 D10
022
8007R2-2
023
858D09-8
A01
251314-2
A02
346449-3
GFD02 NAME PLATE HOUSING SET RUBBER PIN 6 HEX. LABEL SCREW M4X12 HOOK
Q'ty Unit
1 1 2 PC. 2 PC. 1 PC. 0 7 PC. 2 PC. 1 2 PC. 1 PC. 1 PC. ...
Makita GFD02D Reviews
We have not received any reviews for Makita yet.