Makita GFD01Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita GFD01Z manuals!
Problems with Makita GFD01Z?
Ask a Question
Free Makita GFD01Z manuals!
Problems with Makita GFD01Z?
Ask a Question
Popular Makita GFD01Z Manual Pages
GFD01 Instruction Manual - Page 2
... or unplugging the power tool.
Use of a cord suitable for future reference. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
GFD01
Drilling capacities
Steel
20 mm (13/16")
Wood
Auger bit: 50 mm (2") Self...battery cartridges and chargers may differ from heat, oil, sharp edges or moving parts.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents...
GFD01 Instruction Manual - Page 3
... care
1. A charger that have the power tool repaired before turning the power tool on the switch or ... and are not harmful to be caught in the moving parts.
7. Follow all times.
Remove any adjustments, changing accessories... instructions and do not allow you to another battery pack.
2. Use of drugs, alcohol or medication. Recharge only with specifically ...
GFD01 Instruction Manual - Page 4
... battery.
10. SAVE THESE INSTRUCTIONS. Service
1. It may reach or exceed 50 °C (122 °F).
7. Such conduct may make exposed metal parts of the power tool is below when using long drill bits
1. Be sure no load speed
revolutions or reciprocation per minute
Cordless driver drill safety warnings
Safety instructions for tool. Do not modify...
GFD01 Instruction Manual - Page 5
... shortens the battery service life.
3. Charge the battery cartridge if you .
Button 3. CAUTION: Always install the battery cartridge fully... battery cartridge, remove it .
4.
Unless the tool supports the use near a high-voltage electrical power lines, ...bursting causing fires, personal injury and damage. SAVE THESE INSTRUCTIONS. CAUTION: Only use the battery cartridge near a high...
GFD01 Instruction Manual - Page 6
... the application that caused the tool to draw an abnormally high current, the tool stops automatically. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to restart.
Lighting up for about 6 minutes.
Overheat protection
When the ... of use and the ambient temperature, the indication may have the tool serviced at a Makita service center.
GFD01 Instruction Manual - Page 7
...check the direction of rotation before operation. CAUTION: When not operating the tool, always set the speed change the direction of the lamp. Displayed Number
Speed
Torque
Applicable operation
...between the "1" side and "2" side, the tool may be damaged.
Speed change
CAUTION: Always set the reversing switch lever to a complete stop. Arrow
This tool has two action modes.
...
GFD01 Instruction Manual - Page 8
... injury.
2
4
3
1
► 1 . The following shows the rough guide of the same material that you will not be set. Indicator 3.
When you turn the dial while the green light is clean. NOTE...torque level. When the lever displays "1", the torque level in low speed can be able to set the fastening torque level in high speed.
1.
pine)
Hard wood (e.g. Depending on the work...
GFD01 Instruction Manual - Page 9
...
Turn the sleeve counterclockwise to repair. Wood
Soft wood
-
pine)
ø9 x 75
-
ø10 x 90
-
In that case, contact with Makita Authorized or Factory Service Centers to open the chuck jaws...grip to reduce the burden on the tool barrel. Install the side grip so that the tool is switched off . Installing or removing driver bit/ drill bit
CAUTION: Always be fixed at the...
GFD01 Instruction Manual - Page 10
... prevents splitting of the screw.
NOTE: In a cold environment, the tool may cause overheating and damage to the tool.
1
1
2 ► 1 . Installing hook
CAUTION: When installing the hook, always secure it with a screw. Installing driver bit holder
Optional accessory
NOTICE: Do not cover vents, or it may stop the tool to the proper torque level...
GFD01 Instruction Manual - Page 11
...repairs, any assistance for its stated purpose. Drilling operation
First, turn the action mode changing ring so that the tool is switched off and the battery cartridge is removed before proceeding with your Makita tool specified in this manual. The guide screw makes drilling easier by setting...Makita Authorized or Factory Service Centers, always using Makita replacement parts.
11 ENGLISH
In...
GFD01 Parts Breakdown - Page 2
...COMPLETE DIAL CAM COMPRESSION SPRING 3 TERMINAL UNIT GFD01 SERIAL NO. Model GFD01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
266130-9
002
183S38-5
002 C10 263005-3
002 ... 319966-6
A01 C50 962055-2
A02
251314-2
A03
346449-3
TAPPING SCREW BIND PT 3X16 HOUSING SET RUBBER PIN 6 HEX. LOCK NUT M4-7 SPONGE SHEET CAUTION LABEL INC. 2 XGT LOGO...
Makita GFD01Z Reviews
Do you have an experience with the Makita GFD01Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!