Makita CS01Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita CS01Z manuals!
Problems with Makita CS01Z?
Ask a Question
Free Makita CS01Z manuals!
Problems with Makita CS01Z?
Ask a Question
Popular Makita CS01Z Manual Pages
CS01 Instruction Manual - Page 2
... and instructions for advice...shock.
5.
Save all instructions listed below may result...instructions, illustrations and specifications provided with earthed or grounded surfaces, such as in explosive atmo- ENGLISH (Original instructions)
SPECIFICATIONS
Model...specifications herein are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving...
CS01 Instruction Manual - Page 3
...the battery may be entangled. Service
1. Carrying power tools with these instructions to be caught in use...-related hazards.
8. When using only identical replacement parts. Use power tools only with water. This...repaired.
3. Keep cutting tools sharp and clean. Use the power tool, accessories and tool bits etc. If contact accidentally occurs, flush with specifically...
CS01 Instruction Manual - Page 4
...) replace strict adherence to drop or strike battery.
9. Service of...service damaged battery packs. Cordless threaded rod cutter safety warnings
1. Always wear gloves when handling threaded rods. Do not touch the cutting edge or the workpiece immediately after cutting to follow the safety rules stated in this instruction manual... in a safe place.
Installing the batteries to water or...
CS01 Instruction Manual - Page 5
Always stop tool operation and charge the battery cartridge when you notice less tool power.
2.
Overcharging shortens the battery service life.
3. PARTS DESCRIPTION
13
1
14 5
15 4
8
6 9
7
10
4 3 2
12 11
1 Stationary mount 5 Hook
9 Front face 13 Guide scale
2 Movable mount
6 Shoulder strap base (for maintaining maximum battery life
1. Let a hot battery cartridge cool down before...
CS01 Instruction Manual - Page 6
... conditions.
2
► 1 . Overdischarge protection
When the battery capacity becomes low, the tool stops automatically.
Button 3. CAUTION: Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Overheat protection
When the tool is equipped with the indicator
3
1
► 1 . This system automatically cuts off the tool before turning the...
CS01 Instruction Manual - Page 7
Switch action
CAUTION: Before installing the battery cartridge into the tool, always check to see the source of light directly. Auto... switch lever
► 1 . NOTE: After cutting, if you continue to cutting position.
To start the cutting operation, set the reversing switch lever to begin the next cutting sequence. If you release the switch trigger before completing the cut, the ...
CS01 Instruction Manual - Page 8
... tool may result in position depending on the diameter of your desired length on a windy location or a potentially unstable surface. Rod guide (Position 1) 2. Cutting line 3. Rod guide
For a precise cutting, set the rod guide in personal injuries and/or damage to the tool if dropped.
► 1 . CAUTION: When not operating the tool, always fold...
CS01 Instruction Manual - Page 9
... off fractions.
Set the cutting dies onto the mounts so that the tool is released, have the tool serviced at a Makita service center.
► 1 . Bolt 2. Movable mount 5. Set the reversing switch...markings can be seen.
3
1
2
5
4
6
1
2
► 1 .
If not, install the battery and pull the switch trigger until the jaw is damaged. Reversing switch lever
3. Hex wrench...
CS01 Instruction Manual - Page 10
... of the cutting dies are installed to the tool. Check the cutting capacity written on them point each other. When cutting, place the threaded rod perpendicular to set the threaded rod so that the... steel, burrs may break the cutting die and cause personal injury by flown off fractions.
CAUTION: Replace the cutting dies if the cutting edge is chipped or deformed.
► 1 . Burr
10...
CS01 Instruction Manual - Page 11
...guide. Cutting loose threaded rods
When cutting a loose threaded rod on the size of threaded rod
W3/8, 3/8-16UNC, M10
W5/16, W1/4, 5/16-18UNC, 1/4-20UNC, M8, M6
Quitting the cutting in the middle, set...1
► 1. The cover also can be used for supporting the end of the cutting die comes to fully opened position. Rod guide (Position 2)
The cover has markings to indicate its position....
CS01 Instruction Manual - Page 12
...SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Thin side 3. Replace the cutting dies...removed before attempting to the warranty details set forth at the same time. To replace, follow the instructions in the section for installing the cutting dies.
1
2
Carrying/...
CS01 Parts Breakdown - Page 2
...PC. 3 PC. 1 PC. 3 PC. 1 PC. 1 PC. 3 PC. 3 PC. 1 PC. Model CS01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
281019-0
002
941102-2
003
961011-9
004
911213-7
005
183N48-2
005 C10 263002-9
005 ... M5X12 HOUSING SET RUBBER PIN 4 RUBBER PIN 6 INDICATION LABEL CAUTION LABEL INC. 57 LED CIRCUIT LED HOLDER SCREW GUIDE PIN 3 COMPRESSION...
CS01 Parts Breakdown - Page 3
...-6
A01
271445-1
A02
415486-9
A03
458380-2
A04
783202-0
A05
922202-7
A06
199081-0
A07
199444-0
STATOR ROTOR F/R CHANGE LEVER SWITCH C3JW-2CM TERMINAL SQUARE NUT HOUSING SET RUBBER PIN 4 RUBBER PIN 6 INDICATION LABEL CAUTION LABEL INC. 5 PAN HEAD SCREW M5X12 TAPPING SCREW 4X18 CUTTING ARM ASSEMBLY CS01 NAME PLATE CS01 SERIAL NO...
CS01Z New Tool Flyers English - Page 1
... blade changes
SPECIFICATIONS
Battery 12V max...two-position threaded rod guide helps stabilize material for...Set (199081-0) • 1/4" Cutter Blade Set (199444-0) • Depth Gauge • Blade Cover • Hex Wrench
RELATED PRODUCTS
1. 1/4" Cutter Blade Set (199444-0) 2. 3/8" Cutter Blade Set (199081-0)
1
2
3
3. All models...overhead cutting of installed threaded rod including ...
Makita CS01Z Reviews
Do you have an experience with the Makita CS01Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!