Lowrance HELM-1 Drive Unit Support and Manuals
Get Help and Manuals for this Lowrance item
View All Support Options Below
Free Lowrance HELM-1 Drive Unit manuals!
Problems with Lowrance HELM-1 Drive Unit?
Ask a Question
Free Lowrance HELM-1 Drive Unit manuals!
Problems with Lowrance HELM-1 Drive Unit?
Ask a Question
Popular Lowrance HELM-1 Drive Unit Manual Pages
Addendum software release v20.2 for Zeus2 Glass Helm - Page 15
...options are lost after - specify to tracked targets. Hide lost targets. specify to hide targets that support tracking targets, the following distance will also apply to show all AIS targets or specify a maximum... - Show - Bearings Used for both AIS and radar targets.
AIS specific settings are only available if you have a capable AIS device connected to the radar panel illustration.
...
Addendum software release v20.2 for Zeus2 Glass Helm - Page 16
... installation settings. Installation setup settings are described in the Vessels and Tracked Targets dialog.
Antenna setup Used for DSC transmitting devices within range.
AIS targets can set alarms...installation dialog. Safe ring A safe ring can be displayed and tracked. Installation settings must be set in the separate Radar or the display unit's installation manuals.
Addendum software release v20.2 for Zeus2 Glass Helm - Page 21
... received from AIS and DSC vessels. Radar specific settings are shown on security settings, distance, and vessel speed using this option... heading extension lines for your own MMSI (Maritime Mobile Service Identity) number into the system. The length of own... away than the following target filter settings will be hidden: - For radars that support target tracking, the following distance will...
Network Autopilot Installation and Commissioning Manual - Page 50
... a screening braid must have the screen connected as supplied, and the units and cables are shown in supply cables.
rudder drive unit supply cables.
• Keep supply cables as short as possible to ensure compliance with the instructions as shown on the accompanying installation sheet: IS-0777.
4 - 2 Every care has been taken in its design...
Network Autopilot Installation and Commissioning Manual - Page 71
... 24 CHECKING THE COMPASS OFFSET 25 AUTOMATIC RUDDER GAIN 25
CHECKING THE AUTOMATIC RUDDER GAIN LEARNING __________ 26 MANUAL RUDDER GAIN 26 SETTING THE RUDDER GAIN MANUALLY 27
RUDDER GAIN VALUE TABLE 28 BOAT LAG 28 SETTING THE BOAT LAG VALUE 29
BOAT LAG VALUE TABLE 29 CALIBRATION OF DIRECT SPEED INPUT 30 POWER...
Zeus Touch Install Manual - Page 30
... cable (optional for T7 and T8, supplied with another Zeus Touch unit via the network. Access the Video Menu by adjusting the video image settings (brightness, saturation, etc.).
8
Video In
Connect up the video panel buttons. Video In | Zeus Touch installation manual You can optimize the video display by one of the following:
Press...
Zeus Touch Install Manual - Page 44
...Setting the seastate filer • Saiboat setup
Compass calibration Before the compass calibration is started, make sure that there is installed, refer to the instruction for that is reading more significant and heading errors exceeding ±3° may have to be accepted. If another model...setting (the speed at which you want to change the set...-screen instruction, and ... will guide you should...
Zeus Touch Install Manual - Page 45
...which the system automatically changes from slow to the object have the same unit (°M or °T). It can also be set to 3-4 knots to give the best response in a tack. Use ... represents the speed where the hull begins to plane or the speed where you set manually
Autopilot | Zeus Touch installation manual | 45 A deadband of 2 knots is aligned with the bearing line pointing towards...
Network Pilot Installation Manual ACP - Page 71
... 24 CHECKING THE COMPASS OFFSET 25 AUTOMATIC RUDDER GAIN 25
CHECKING THE AUTOMATIC RUDDER GAIN LEARNING __________ 26 MANUAL RUDDER GAIN 26 SETTING THE RUDDER GAIN MANUALLY 27
RUDDER GAIN VALUE TABLE 28 BOAT LAG 28 SETTING THE BOAT LAG VALUE 29
BOAT LAG VALUE TABLE 29 CALIBRATION OF DIRECT SPEED INPUT 30 POWER...
Zeus Glass Helm Installation Manual - Page 47
processor unit only 1060 grams
Dimensions (overall) Electrical
... baud rate Charting support
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Embedded low detail backround +
Insight, Navionics and CMap on rear (BNC female. 7
Specifications
Mechanical/Environmental
Casing
ABS... male, LEN = 1)
Video input
2 ports on SD card
Specifications | Zeus2 Glass Helm Installation Manual
| 45
NAIS 400 Owners Manual - Page 27
...instructions in Figure 13. Specific details of features, your vessel on their chartplotter or PC. Using proAIS2 with AIS transceivers installed... chartplotter manual.
You should see your AIS transceiver must be installed as shown in Step 4 and 5 under Installation procedures...
Using the AIS transceiver
Once the unit has been configured, it to set the AIS transceiver into 'silent mode...
NSPL 400 User Manual - Page 2
... to make changes to specifications without notice.
tion to a comment or other information relating to the product (Documentation) may not be the official version of printing. Warranty The warranty card is the owner's sole responsibility to draw the reader's atten- It is supplied as at any instruction manuals, user guides and other important information...
H2000 User Manual - Page 94
...and the wind at the root of the wind at ground level and the wind aloft; h2000 User Manual
CAL VAL 2 Setting 0
1
Description
Default setting. if the wind is wind shear and wind gradient.
Uses an external boat speed source. The ... to overcome, which starts off almost completely unmixed. The best example of the greatest problems for an instrument system to the main processor.
H2000 User Manual - Page 114
...If the sensor is a totally independent fitting (B&G part no. 224-00-065) then it is necessary...sensor selection value. The paddle-wheel has a sensor incorporated within it, in :
114
HB-0845-06 h2000 User Manual
CAL VAL 2 Setting 0 1 2 3 4 5
Function Text Shown
AFT DPTH FWD DPTH MID DPTH PORT DEP STBD DEP DEPTH ... supply at terminals 18 (+) and 17 (-) at the Computer Unit connection block.
Network Quad User Manual - Page 20
When the alarm condition is met the unit will also sound their alarms and flash their displays, except Network WIND and Network TACK which do not have alarms. See NETWORK ALARMS at the end of this manual.
Deep Alarm • Factory set to 1.0m, (3.2ft, 0.5 fathoms). • Adjustable range 0 - 180m, 0 - 590ft, 0 - 98.4 fa. The...
Lowrance HELM-1 Drive Unit Reviews
We have not received any reviews for Lowrance yet.