Dimension Guide
Page 1
... current AHAM/IAPMO test standards, is connected to change materials and specifications without notice. (1.9 cm) A Page 1 of 12' (3.7 m) (Part No. 3385556) that meets the wiring requirements for planning purposes only. If required, the air gap should be looped up and securely fastened to... or disposer inlet. Specifications subject to house plumbing lower than 20" Use ¹⁄₂" (1.3 cm) minimum I.D. Use a U.L.-listed or CSA-approved conduit connector. Follow the kit instructions for use with 20 to 120 psi (138 to improve Dimensions are for your dishwasher...
... current AHAM/IAPMO test standards, is connected to change materials and specifications without notice. (1.9 cm) A Page 1 of 12' (3.7 m) (Part No. 3385556) that meets the wiring requirements for planning purposes only. If required, the air gap should be looped up and securely fastened to... or disposer inlet. Specifications subject to house plumbing lower than 20" Use ¹⁄₂" (1.3 cm) minimum I.D. Use a U.L.-listed or CSA-approved conduit connector. Follow the kit instructions for use with 20 to 120 psi (138 to improve Dimensions are for your dishwasher...
Installation Guide
Page 3
...: Drain hose Drain hose 2 - Read and follow the instructions provided with any tools listed here. INSTALLATION REQUIREMENTS Tools and Parts Gather the recommended tools and parts before starting installation. counter custom (1 large and head mounting tape 1 small) screws (2) brackets (top) Parts needed : Cordless drill with certain models only: Bottom sound pad (located in lower...
...: Drain hose Drain hose 2 - Read and follow the instructions provided with any tools listed here. INSTALLATION REQUIREMENTS Tools and Parts Gather the recommended tools and parts before starting installation. counter custom (1 large and head mounting tape 1 small) screws (2) brackets (top) Parts needed : Cordless drill with certain models only: Bottom sound pad (located in lower...
Installation Guide
Page 6
...185;⁄₂" minimum I.D. If drain hose is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part Number 3385556) that meets the wiring requirements for use an air gap if the drain hose is resistant to heat and detergent, and fits the... licensed plumber. • 120°F (49°C) water at dishwasher O.D. If connecting dishwasher with a power supply cord: • Use UL Listed power supply cord kit (Part Number 4317824) marked for your dishwasher. Drain Requirements • A new drain hose is not recommended. • A 90° elbow with ...
...185;⁄₂" minimum I.D. If drain hose is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part Number 3385556) that meets the wiring requirements for use an air gap if the drain hose is resistant to heat and detergent, and fits the... licensed plumber. • 120°F (49°C) water at dishwasher O.D. If connecting dishwasher with a power supply cord: • Use UL Listed power supply cord kit (Part Number 4317824) marked for your dishwasher. Drain Requirements • A new drain hose is not recommended. • A 90° elbow with ...
Installation Guide
Page 12
...facing to avoid damaging floor covering. Retain for later use. 4 Route cord so that it does not touch dishwasher motor to lower part of electrical connection will you use door panel as a worktable without first covering with a towel to avoid scratching the door panel. Using... hex head socket, nut driver or Phillips screwdriver, remove 2 screws attaching access panel and lower panel to 16-gauge dishwasher wiring. Install a UL Listed/CSA Approved strain relief. Power Supply Cord: Follow Option A instructions Direct Wire: Follow Option B instructions NOTE: If using Option B, proceed to ...
...facing to avoid damaging floor covering. Retain for later use. 4 Route cord so that it does not touch dishwasher motor to lower part of electrical connection will you use door panel as a worktable without first covering with a towel to avoid scratching the door panel. Using... hex head socket, nut driver or Phillips screwdriver, remove 2 screws attaching access panel and lower panel to 16-gauge dishwasher wiring. Install a UL Listed/CSA Approved strain relief. Power Supply Cord: Follow Option A instructions Direct Wire: Follow Option B instructions NOTE: If using Option B, proceed to ...
Installation Guide
Page 20
... Approved strain relief in type strain relief. Strain relief is connected, remove towel. Select UL Listed/CSA Approved twist-on water supply and check for leaks. Visit www.kitchenaid.com/watersupply under drain hose to catch any water in Cabinet Opening" section. If needed , see website for ...Route cable so that it does not touch dishwasher motor or lower part of the drain hose. Turn on wire connectors (not included) rated to connect your household wiring to "Secure Dishwasher in drain hose. Visit www.kitchenaid.com/drain under 90° elbow fitting. 2 Check for leaks...
... Approved strain relief in type strain relief. Strain relief is connected, remove towel. Select UL Listed/CSA Approved twist-on water supply and check for leaks. Visit www.kitchenaid.com/watersupply under drain hose to catch any water in Cabinet Opening" section. If needed , see website for ...Route cable so that it does not touch dishwasher motor or lower part of the drain hose. Turn on wire connectors (not included) rated to connect your household wiring to "Secure Dishwasher in drain hose. Visit www.kitchenaid.com/drain under 90° elbow fitting. 2 Check for leaks...