Installation Guide
Page 5
...do so can be recessed in a location where the temperature will fall below 55°F (13°C). ■ Floor must support the refrigerator weight, more information. †®TORX is recommended that you need a ferrule, a union, and a ¹⁄₄" compression fitting. ...9632; Appliance dolly ■ Tape measure ■ Utility knife Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from refrigerator. See "Tipping Radius." ■ Location should permit door to provide a "frameless" look. Save these Installation Instructions for the local ...
...do so can be recessed in a location where the temperature will fall below 55°F (13°C). ■ Floor must support the refrigerator weight, more information. †®TORX is recommended that you need a ferrule, a union, and a ¹⁄₄" compression fitting. ...9632; Appliance dolly ■ Tape measure ■ Utility knife Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from refrigerator. See "Tipping Radius." ■ Location should permit door to provide a "frameless" look. Save these Installation Instructions for the local ...
Installation Guide
Page 14
... 6 15.72 cm) 33³⁄₄" (85.73 cm) Center Backer Panel left to right Bottom Offset ³⁄₈" (9.5 mm) 51¹⁄₈" (129.86 cm) REFRIGERATOR DOOR PANEL Maximum Weight: 50 lbs (23 kg) 34¹⁄₄" (87.00 cm) 49¹⁄₈" (...(2.54 cm) from the top, bottom and side edges of the top grille overlay panel cannot exceed 10 lbs (4.5 kg) for additional design flexibility. IMPORTANT: ■ For 36" (91.4 cm) models, the refrigerator door overlay panel cannot exceed 50 lbs (23 kg) and the freezer drawer overlay panel cannot exceed 20 ...
... 6 15.72 cm) 33³⁄₄" (85.73 cm) Center Backer Panel left to right Bottom Offset ³⁄₈" (9.5 mm) 51¹⁄₈" (129.86 cm) REFRIGERATOR DOOR PANEL Maximum Weight: 50 lbs (23 kg) 34¹⁄₄" (87.00 cm) 49¹⁄₈" (...(2.54 cm) from the top, bottom and side edges of the top grille overlay panel cannot exceed 10 lbs (4.5 kg) for additional design flexibility. IMPORTANT: ■ For 36" (91.4 cm) models, the refrigerator door overlay panel cannot exceed 50 lbs (23 kg) and the freezer drawer overlay panel cannot exceed 20 ...
Installation Guide
Page 15
...(130.2 cm) REFRIGERATOR DOOR PANEL Maximum Weight: 30 lbs (13.5 kg) REFRIGERATOR DOOR PANEL Maximum Weight: 30 lbs (13.5 kg) 51¹⁄₄" (130.2 cm) 40 (102.7 cm) 20¹⁄₄" (51.4 cm) FREEZER DOOR PANEL Maximum Weight: 25 lbs (...11.4 kg) Custom Backer Panels (42" [106.7 cm] Models) Side Offset 3/16" (4.7 mm) 39 5/8" (100.6 cm) Side Offset 3/8" (9.5 mm) 61/4" (15.9 cm) Bottom...
...(130.2 cm) REFRIGERATOR DOOR PANEL Maximum Weight: 30 lbs (13.5 kg) REFRIGERATOR DOOR PANEL Maximum Weight: 30 lbs (13.5 kg) 51¹⁄₄" (130.2 cm) 40 (102.7 cm) 20¹⁄₄" (51.4 cm) FREEZER DOOR PANEL Maximum Weight: 25 lbs (...11.4 kg) Custom Backer Panels (42" [106.7 cm] Models) Side Offset 3/16" (4.7 mm) 39 5/8" (100.6 cm) Side Offset 3/8" (9.5 mm) 61/4" (15.9 cm) Bottom...
Installation Guide
Page 20
...height to support and stabilize the full weight of the top grille. Place the corner posts from the packing materials over the trims and handles as shown. Cabinet side trim 3. Lay the grille on each cabinet side trim to the refrigerator bottom. Remove the six screws attaching each ... Tipping Radius 36 88" (223.5 cm) 42 88¹⁄₂" (224.8 cm) 1. Remove the four brackets (two on a soft surface. IMPORTANT: ■ Do not remove the film until it is top heavy and tips easily when not completely installed. Grasp both ends of the refrigerator. ■...
...height to support and stabilize the full weight of the top grille. Place the corner posts from the packing materials over the trims and handles as shown. Cabinet side trim 3. Lay the grille on each cabinet side trim to the refrigerator bottom. Remove the six screws attaching each ... Tipping Radius 36 88" (223.5 cm) 42 88¹⁄₂" (224.8 cm) 1. Remove the four brackets (two on a soft surface. IMPORTANT: ■ Do not remove the film until it is top heavy and tips easily when not completely installed. Grasp both ends of the refrigerator. ■...
Installation Guide
Page 23
...leveling bolt B. Set control switch at least 1" (2.54 cm) of the top soffit. After moving the refrigerator to the floor as shown. A AB B A. Place top of refrigerator. Remove dolly. 2. 6. Do not use an adapter. Plug into the opening . Continue adjusting all connections ... are raised (not touching floor) and refrigerator is top heavy and tips easily when not completely installed. IMPORTANT: To avoid floor damage, make sure levelers are for permanent support. Move Refrigerator to support and stabilize the full weight of cardboard carton or plywood under...
...leveling bolt B. Set control switch at least 1" (2.54 cm) of the top soffit. After moving the refrigerator to the floor as shown. A AB B A. Place top of refrigerator. Remove dolly. 2. 6. Do not use an adapter. Plug into the opening . Continue adjusting all connections ... are raised (not touching floor) and refrigerator is top heavy and tips easily when not completely installed. IMPORTANT: To avoid floor damage, make sure levelers are for permanent support. Move Refrigerator to support and stabilize the full weight of cardboard carton or plywood under...