Kenwood XR-4S - 1200W Reference Fit Digital Power Amplifier Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood XR-4S manuals!
Problems with Kenwood XR-4S?
Ask a Question
Free Kenwood XR-4S manuals!
Problems with Kenwood XR-4S?
Ask a Question
Kenwood XR-4S Videos
Modulo kenwood XR 4S
Duration: 8:48
Total Views: 346
Duration: 8:48
Total Views: 346
Kenwood XR-4S
Duration: 1:25
Total Views: 1,461
Duration: 1:25
Total Views: 1,461
Modulo kenwood XR 4S MONTADO!!
Duration: 3:42
Total Views: 259
Duration: 3:42
Total Views: 259
Popular Kenwood XR-4S Manual Pages
Owner's Manual (pdf) - Page 1
Model XR-4S/KAC-X4D Serial number US Residence Only
Register Online
Register your Kenwood dealer for information or service on the warranty card, and in the space provided below. XR-4S KAC-X4D
FOUR CHANNEL DIGITAL POWER AMPLIFIER 3 page 2-13
INSTRUCTION MANUAL
AMPLIFICATEUR 4 CANAUX DIGITAL 3 page 14-25
MODE D'EMPLOI
AMPLIFICADOR DE POTENCIA DIGITAL DE CUATRO CANALES 3 página 26-36...
Owner's Manual (pdf) - Page 2
...digital device, pursuant to Part 15 of the unit...Kenwood dealer.
• If the unit does not seem to be determined by one or more of water splashing. • When replacing...instruction manual.
However, there is encouraged to try to direct
sunlight or excessive heat or humidity.
These limits are expressly approved in a residential installation... you experience problems during use ...
Owner's Manual (pdf) - Page 3
... it depletes the battery.
Wh4eΩn more than one set of speakers are going to you. Old electrical and electronic... Contact your speakers4Ωfrom various accidents or problems that are going
to be connected should be ... DC signal is not connected.
• Be sure to install a protective fuse in Watts) of the car chassis that acts...amplifier are
going to a metal part of the...
Owner's Manual (pdf) - Page 4
...carpet. Install the amplifier in a place where people, resins, and other damage.
• Do not install near the dashboard, rear tray, or air bag safety parts.
• The installation to ...installing the unit, check to select the proper setting and connection. 1. Connect the input and output wires of settings and connections possible according to applications, read the instruction manual...
Owner's Manual (pdf) - Page 6
Connection
* Commercially available parts
WARNING
Remove the ignition key and disconnect the negative · terminal of the battery to prevent short circuits.
GND
LEFT
RIGHT
P.CON
BRIDGED SPEAKER OUTPUT A
...
Owner's Manual (pdf) - Page 7
...sure to turn the power off before changing the setting of any switch.
• If the fuse blows, check wires for shorts, then replace the fuse with the following thicknesses:
Battery wire and... ground wire
AWG 4 - Wire Thicknesses You can cause this unit to fail.
• After installation, check that no ...
Owner's Manual (pdf) - Page 9
... fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Power control terminal Controls the unit ON/OFF.
One amplifier is referred to connect it with a large...
RIGHT
LINE IN
L
BRIDGED SPEAKER OUTPUT A
R
BRIDGED SPEAKER OUTPUT B
A
B
This is amplifier B. When multiple speakers are used . (Make connections to the LEFT channel 9 and the RIGHT channel &#...
Owner's Manual (pdf) - Page 10
...control adjusts the frequency band output from this control according to amplifiers A and B. • A position: Amplifies only signal input amplifier A with both amplifiers A and B.
8 INPUT SENSITIVITY control (A.ch/B.ch) Set this ...INPUT SEL. NOTE
For the pre-output level, refer to the in the instruction manual of the center unit connected with the "FILTER FREQUENCY" control.
- RANGE...
Owner's Manual (pdf) - Page 12
... speaker wire again so
in your unit may be set to the correct position.
Troubleshooting Guide
What might appear to be a malfunction in the car body. The output level is not pinched by referring to .
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
No sound.
• Input (or output...
Owner's Manual (pdf) - Page 13
...;) (1 kHz, 1.0 % THD)...300 W × 2
Frequency Response (+0, -1 dB)...20 Hz - 20 kHz
Sensitivity (rated output) (MAX.) ...0.2 V
(MIN.) ...5.0 V
Input Impedance...10 kΩ
Signal to change without notice. Specifications
Specifications subject to Noise Ratio...105 dB
Low Pass Filter Frequency (-12 dB/oct.)
Low Range...50 Hz - 200 Hz (variable)
High Range...2.5 kHz - 10 kHz...
Kenwood XR-4S Reviews
We have not received any reviews for Kenwood yet.