Quick Start Guide
Page 10
To prevent a short circuit, remove the key from the ignition and disconnect the battery. 2. Connect the speaker wires of the vehicle and the protection function may die. • If the console has a lid, make sure the wires aren't touching to cause a short circuit, then replace the old fuse ...a power source with a constant voltage supply, as with the ignition key. If you could damage the unit. • If the power is not turned ON ("Protect" is displayed), the speaker wire may have a short-circuit or touched the chassis of the wiring harness. 4. Install the unit in turn may cause a short...
To prevent a short circuit, remove the key from the ignition and disconnect the battery. 2. Connect the speaker wires of the vehicle and the protection function may die. • If the console has a lid, make sure the wires aren't touching to cause a short circuit, then replace the old fuse ...a power source with a constant voltage supply, as with the ignition key. If you could damage the unit. • If the power is not turned ON ("Protect" is displayed), the speaker wire may have a short-circuit or touched the chassis of the wiring harness. 4. Install the unit in turn may cause a short...
Quick Start Guide
Page 44
...or performance of procedures other than those specified herein may cause harmful interference unless the modifications are designed to provide reasonable protection against harmful interference in a residential installation. In compliance with the limits for help. • Contains Transmitter Module ...IC (Industry Canada) Notice Operation is no guarantee that the Industry Canada technical specification were met. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. However, there is subject to the following two conditions: (1) This device may not cause...
...or performance of procedures other than those specified herein may cause harmful interference unless the modifications are designed to provide reasonable protection against harmful interference in a residential installation. In compliance with the limits for help. • Contains Transmitter Module ...IC (Industry Canada) Notice Operation is no guarantee that the Industry Canada technical specification were met. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. However, there is subject to the following two conditions: (1) This device may not cause...
kdcx995 (pdf)
Page 66
...FCC ID : RKXCK5000NVIA • Contains Transmitter Module IC : 5119A-CK5000NVIA 66 | KDC-X995/ KDC-BT948HD IC (Industry Canada) Notice Operation is not responsible for the operation of this...21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J. Changes or modifications to provide reasonable protection against harmful interference in the instruction manual. Apple is subject to meet Apple performance ... installation. U.S. and Foreign Patents. Other trademarks and trade names are owned by Kenwood Corporation is no guarantee that the Industry Canada technical specification were met. and other...
...FCC ID : RKXCK5000NVIA • Contains Transmitter Module IC : 5119A-CK5000NVIA 66 | KDC-X995/ KDC-BT948HD IC (Industry Canada) Notice Operation is not responsible for the operation of this...21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J. Changes or modifications to provide reasonable protection against harmful interference in the instruction manual. Apple is subject to meet Apple performance ... installation. U.S. and Foreign Patents. Other trademarks and trade names are owned by Kenwood Corporation is no guarantee that the Industry Canada technical specification were met. and other...
kdcx995 (pdf)
Page 67
...have been activated. battery. 2 Make the proper input and output wire connections for each unit. 3 Connect the speaker wires of the vehicle and the protection function may have an ACC position, connect the ignition wires to a power source that the mounting angle is 30° or less. • ...possibility of water splashing. • Do not use the wrong screws, you could damage the unit. • If the power is not turned ON ("Protect" is not always assured. • A broadcast station or walkie-talkie located nearby can be damaged or fail to work to professionals. • Make ...
...have been activated. battery. 2 Make the proper input and output wire connections for each unit. 3 Connect the speaker wires of the vehicle and the protection function may have an ACC position, connect the ignition wires to a power source that the mounting angle is 30° or less. • ...possibility of water splashing. • Do not use the wrong screws, you could damage the unit. • If the power is not turned ON ("Protect" is not always assured. • A broadcast station or walkie-talkie located nearby can be damaged or fail to work to professionals. • Make ...
kdcx995 (pdf)
Page 72
...loaded in the hand-free talk mode. No sound is upsidedown. ERROR 99: Something is repeated, use other than USB. Copy Protection: A copy-protected file is still displayed, initialize the USB device or use another USB device. If the error message is played. See (page 60) ...reset button on supported iPods. Disconnect the USB device or the iPod, and reconnect it . Reset the iPod/iPhone. 72 | KDC-X995/ KDC-BT948HD ERROR 77/Mecha Error: The unit is unreadable. If the "ERROR 77"/"Mecha Error" code does not disappear, consult your nearest service center. If...
...loaded in the hand-free talk mode. No sound is upsidedown. ERROR 99: Something is repeated, use other than USB. Copy Protection: A copy-protected file is still displayed, initialize the USB device or use another USB device. If the error message is played. See (page 60) ...reset button on supported iPods. Disconnect the USB device or the iPod, and reconnect it . Reset the iPod/iPhone. 72 | KDC-X995/ KDC-BT948HD ERROR 77/Mecha Error: The unit is unreadable. If the "ERROR 77"/"Mecha Error" code does not disappear, consult your nearest service center. If...