Instruction Manual
Page 2
... Setting Text Scroll Built-in Auxiliary input Setting CD Read Setting Demonstration mode Setting Basic Operations of remote control 23 Accessories/ Installation Procedure 25 Connecting Wires to Terminals 26 Installation 27 Troubleshooting Guide 29 Specifications 31 2 | English
... Setting Text Scroll Built-in Auxiliary input Setting CD Read Setting Demonstration mode Setting Basic Operations of remote control 23 Accessories/ Installation Procedure 25 Connecting Wires to Terminals 26 Installation 27 Troubleshooting Guide 29 Specifications 31 2 | English
Instruction Manual
Page 3
...normally after a while, consult your Kenwood dealer for connectable models of water splashing. • Do not place the faceplate (and the faceplate case) in areas exposed to direct sunlight, excessive heat or humidity. For safety's sake, leave the mounting and wiring work to professionals. 2CAUTION To ... precautions 2WARNING To prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any Kenwood disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. Using a...
...normally after a while, consult your Kenwood dealer for connectable models of water splashing. • Do not place the faceplate (and the faceplate case) in areas exposed to direct sunlight, excessive heat or humidity. For safety's sake, leave the mounting and wiring work to professionals. 2CAUTION To ... precautions 2WARNING To prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any Kenwood disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. Using a...
Instruction Manual
Page 10
... system comes back ON. Refer to the audio during a call comes in "CALL" is locked in its faceplate case while detached. (Faceplate case: Accessory of KDC-MP2035/MP235/ MP235CR) • Do not expose the faceplate (and the faceplate case) to direct sunlight or excessive heat or humidity. Reattaching the Faceplate 1 Align the... the unit can be detached and taken with you to detach it clicks. When the call comes in . When a call ends Hang up the MUTE wire to your telephone using a commercial telephone accessory.
... system comes back ON. Refer to the audio during a call comes in "CALL" is locked in its faceplate case while detached. (Faceplate case: Accessory of KDC-MP2035/MP235/ MP235CR) • Do not expose the faceplate (and the faceplate case) to direct sunlight or excessive heat or humidity. Reattaching the Faceplate 1 Align the... the unit can be detached and taken with you to detach it clicks. When the call comes in . When a call ends Hang up the MUTE wire to your telephone using a commercial telephone accessory.
Instruction Manual
Page 25
.... • If your car. 7. Accessories/ Installation Procedure Accessories 1 2 3 4 5 ..........1 ..........2 ..........4 ..........4 ..........1 Installation Procedure 1. Connect the wiring harness connector to both the rear output terminals (do not mix front and rear). battery. 8. Reconnect the - Press the reset button. 2WARNING If...circuit, remove the key from the ignition and disconnect the - Make the proper input and output wire connections for each unit. 3. Connect the wiring harness wires in your car's ignition does not have a short-circuit or touched the chasis of the left...
.... • If your car. 7. Accessories/ Installation Procedure Accessories 1 2 3 4 5 ..........1 ..........2 ..........4 ..........4 ..........1 Installation Procedure 1. Connect the wiring harness connector to both the rear output terminals (do not mix front and rear). battery. 8. Reconnect the - Press the reset button. 2WARNING If...circuit, remove the key from the ignition and disconnect the - Make the proper input and output wire connections for each unit. 3. Connect the wiring harness wires in your car's ignition does not have a short-circuit or touched the chasis of the left...
Instruction Manual
Page 26
...) - (To car chassis) P.CONT Power control/Motor antenna control wire (Blue/White) Connect to the relevant instruction manuals. Connecting Wires to Terminals To Kenwood disc changer/ External optional accessory (KDC-MP2035/MP235 only) ⁄ To connect these leads, refer to the terminal that is grounded when either to the power control terminal when using the...
...) - (To car chassis) P.CONT Power control/Motor antenna control wire (Blue/White) Connect to the relevant instruction manuals. Connecting Wires to Terminals To Kenwood disc changer/ External optional accessory (KDC-MP2035/MP235 only) ⁄ To connect these leads, refer to the terminal that is grounded when either to the power control terminal when using the...
Instruction Manual
Page 30
... disc. READING: The unit is wrong with a format that the unit can 't support. ➪ ---- PROTECT: NA FILE: COPY PRO: DEMO: The speaker wire has a short-circuit or touches the chassis of the slave unit being exchanged in the Disc changer. If the "PROTECT" code does not disappear, consult... Discs are recorded on the unit. The disc magazine is not operating properly. ➪ Reinsert the CD. E-77: The unit is activated. ➪ Wire or insulate the speaker cable properly and press the reset button. NO DISC: No disc has been loaded in the changer. If the "E-77" code...
... disc. READING: The unit is wrong with a format that the unit can 't support. ➪ ---- PROTECT: NA FILE: COPY PRO: DEMO: The speaker wire has a short-circuit or touches the chassis of the slave unit being exchanged in the Disc changer. If the "PROTECT" code does not disappear, consult... Discs are recorded on the unit. The disc magazine is not operating properly. ➪ Reinsert the CD. E-77: The unit is activated. ➪ Wire or insulate the speaker cable properly and press the reset button. NO DISC: No disc has been loaded in the changer. If the "E-77" code...