Instruction Manual
Page 1
...the serial number, found on the back of the unit, in the spaces designated on the product. Refer to read through this instruction manual. KAC-8404 4/3/2 CHANNEL POWER AMPLIFIER 7 page 2-5 INSTRUCTION MANUAL AMPLIFICATEUR DE PUISSANCE 4/3/2 CANAUX 7 page 6-9 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA DE 4/3/2 CANALES 7 página ...time to the model and serial numbers whenever you obtain the best performance from your Kenwood product at www.kenwoodusa.com © B64-3935-00/00 (KV/EV) For your Kenwood dealer for information or service on the warranty card, and in the space provided below...
...the serial number, found on the back of the unit, in the spaces designated on the product. Refer to read through this instruction manual. KAC-8404 4/3/2 CHANNEL POWER AMPLIFIER 7 page 2-5 INSTRUCTION MANUAL AMPLIFICATEUR DE PUISSANCE 4/3/2 CANAUX 7 page 6-9 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA DE 4/3/2 CANALES 7 página ...time to the model and serial numbers whenever you obtain the best performance from your Kenwood product at www.kenwoodusa.com © B64-3935-00/00 (KV/EV) For your Kenwood dealer for information or service on the warranty card, and in the space provided below...
Instruction Manual
Page 2
... capacity than the output power (in Watts) of the amplifier. Declaration of Conformity with regard to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The ...to directly contact the edge of the iron plate by turning the equipment off . This equipment may generate or use a new one power amplifier are going to be connected should be 2Ω or greater (for stereo connections), or 4Ω or greater (for EU countries that...
... capacity than the output power (in Watts) of the amplifier. Declaration of Conformity with regard to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The ...to directly contact the edge of the iron plate by turning the equipment off . This equipment may generate or use a new one power amplifier are going to be connected should be 2Ω or greater (for stereo connections), or 4Ω or greater (for EU countries that...
Instruction Manual
Page 3
...location, In a place that gets hot, In a place that gets direct sunlight, In a location that are sensitive to easily dissipate. English 3 Install the amplifier in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. •... function is not connected to make sure that there is nothing hazardous on top of the unit. • The surface temperature of the amplifier will not come into contact with a protection function for protecting this order. 6.Install the installation fittings in the unit. 7.Attach the unit...
...location, In a place that gets hot, In a place that gets direct sunlight, In a location that are sensitive to easily dissipate. English 3 Install the amplifier in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. •... function is not connected to make sure that there is nothing hazardous on top of the unit. • The surface temperature of the amplifier will not come into contact with a protection function for protecting this order. 6.Install the installation fittings in the unit. 7.Attach the unit...
Instruction Manual
Page 5
...9758; Set switches properly by referring to . ✔ Volume is too high. ☞ Replace the fuse and use as a stereo amplifier. • MONO (Lch) position: Amplifies the signal input from the left side only. Use the diagram on , the protection function may be activated. If the Power indicator ... 2 Illumination 3 FILTER FREQUENCY control (A.ch/B.ch) Sets the cutoff frequency when the "FILTER" switch is OFF. Remove the cover to access to its controls for amplifier B only. • ON position: BASS BOOST is +18 dB. • OFF position: BASS BOOST is set to "LPF" or "HPF". 4 INPUT ...
...9758; Set switches properly by referring to . ✔ Volume is too high. ☞ Replace the fuse and use as a stereo amplifier. • MONO (Lch) position: Amplifies the signal input from the left side only. Use the diagram on , the protection function may be activated. If the Power indicator ... 2 Illumination 3 FILTER FREQUENCY control (A.ch/B.ch) Sets the cutoff frequency when the "FILTER" switch is OFF. Remove the cover to access to its controls for amplifier B only. • ON position: BASS BOOST is +18 dB. • OFF position: BASS BOOST is set to "LPF" or "HPF". 4 INPUT ...