Kenwood 6402 - KAC Amplifier Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood 6402 manuals!
Problems with Kenwood 6402?
Ask a Question
Free Kenwood 6402 manuals!
Problems with Kenwood 6402?
Ask a Question
Popular Kenwood 6402 Manual Pages
Instruction Manual - Page 2
...Refer to page 5)
Accessories
Part name
Self-tapping screws (ø...installation, consult your Kenwood dealer.
• If the unit does not seem to be working right, consult your unit to malfunction. • To prevent a short circuit when replacing...problems. When Protection operates, the indicator informs you experience problems during use because the surface of the unit. • Do not install...
Instruction Manual - Page 3
Install the amplifier in a place where
people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the vehicle should securely fasten the unit to a place in which allows heat to make sure that electrical equipment such as a gasoline tank, brake ...
Instruction Manual - Page 4
... of the signals input to amplifiers A and B. • A position: Amplifies only signal input amplifier A with both amplifiers A and B.
4 FILTER FREQUENCY control (A.ch/B.ch) Sets the cutoff frequency when the FILTER switch is used to select the operation mode of the amplifier.
• STEREO position: The amplifier can be used as a guide. Use the diagram on the right as...
Instruction Manual - Page 5
... speakers from various accidents or problems that can occur. terminal. English 5 When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. • When...8226; When a ground wire of trouble.
■ The protection function is activated in the following situations: This unit is not connected to a metal part serving as an electrical ground passing...
Instruction Manual - Page 6
... each channel. • Bridged Connections: When you wish to use the unit as a stereo amplifier, stereo connections are used . (Make connections to the LEFT channel 9 and the RIGHT channel ... output of no less than 40 W.
• Do not connect the speaker output leads from a power amplifier (Optional) to be turned ON/OFF by the ignition key switch (ACC line). When multiple speakers are ...
Instruction Manual - Page 7
...
negative - Set the unit according to a metal part of the amplifier. terminal of...Install the unit in Watts) of the car chassis that no unconnected wires or connectors are large variety of settings and connections possible according to applications, read the instruction manual well to be connected should be the same capacity as an electrical ground passing electricity to the amplifier...
Instruction Manual - Page 9
...*
25
(Bridged Connections)
!
25
■ Power wire connection
25
Terminal cover
8 90
Power control wire Battery wire*
Ground wire*
Protective Fuse*
Battery
* Commercially available parts
A channel Left speaker A channel Right speaker
B channel Right speaker B channel Left speaker A channel Speaker (Bridged)
B channel Speaker (Bridged)
Lead terminal*
English 9 ■ Speaker wire...
Instruction Manual - Page 11
... low frequencies. (High pass)
C=
159000 fc x R
(µF)
L=
159 x R fc
(mH)
fc=Cut of Frequency (Hz) R=Speaker Impedance (Ω)
●Example: When it is required to set a crossover frequency of 120 Hz using a coil and capacitor...in a drop of the combined impedance with the closest ratings to the results calculated from the...
Instruction Manual - Page 12
... result of slight misoperation or miswiring. of the short, replace
the fuse.
The output level is pinched by anything.
• The switches may be set to the correct
to be a malfunction in the car body. Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
No sound.
• Input (or...
Instruction Manual - Page 13
... Ω) (1 kHz, 0.8 % THD)...100 W x 2 Frequency Response (+0, -3 dB) ...10 Hz - 45 kHz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Signal to change without notice. Specifications
Specifications subject to Noise Ratio...100 dB Input Impedance...10 kΩ Low Pass Filter Frequency (12 dB/oct.) ...50 - 200 Hz (variable) High Pass Filter Frequency (...
Kenwood 6402 Reviews
We have not received any reviews for Kenwood yet.