Jensen POWER1050 - Mono Amplifier Support and Manuals
Get Help and Manuals for this Jensen item
View All Support Options Below
Free Jensen POWER1050 manuals!
Problems with Jensen POWER1050?
Ask a Question
Free Jensen POWER1050 manuals!
Problems with Jensen POWER1050?
Ask a Question
Popular Jensen POWER1050 Manual Pages
Operation Manual - Page 3
... baseline when comparing amplifiers of the way, so please keep reading. If you 'll be fair to the competition, we rate our amps in the first ...power you and to you are getting. So feel confident that your Jensen purchase decision was a sound one, and remember "If it ," is whether the power can permanently damage your ability to install your Jensen amplifier should ever require service...
Operation Manual - Page 4
...
Power 900
• 300 x 1 Watts, 4-Ohm • 450 x 1 Watts, 2-Ohm
Power 920
• 100 x 4 Watts, 4-Ohm • 140 x 4 Watts, 2-Ohm • 230 x 2 Watts, 4-Ohm Bridged Stereo
Power 1050
• 350 x 1 Watts, 4-Ohm • 525 x 1 Watts, 2-Ohm
Specifications subject to no one. POWER Amplifiers
Features and Specifications
Your new Jensen Power mobile stereo power amplifier is the amplifier...
Operation Manual - Page 5
..., or visit www.jensen.com at least a #8 gauge wire. Supplies
• Black electrical tape • Amplifier Installation Kit
Tools
• Cordless drill with carpets or enclose it was designed to do not let your amp be two (2) ground wires coming from corrosion, rust or dirt.
Follow the installation instructions carefully, or have the amplifier installed correctly. Also...
Operation Manual - Page 6
... the power to your amplifier(s):
MODEL NUMBER 400 760 880 900 920 1050
MAX CURRENT DRAW 25A 40A 60A 60A 60A 100A
MIN WIRE GAUGE #8 #8 #6 #6 #6 #4
Power Terminal (+12V/B+)
Connect the main power wire to the amplifier remote terminal. Use the following recommended wire gauge as close to ground. Battery Terminal Adaptor
Fuse or Circuit Breaker
Install as a guide when installing...
Operation Manual - Page 7
...)
Model 400 760 880 900 920 1050
Quantity 1 2 2 2 2 4
Amps 25 20 30 30 30 25
Type ATO ATO ATO ATO ATO ATO
5
POWER Amplifiers Ground Terminal (GND)
Make the ground lead as short as possible, leaving enough length to complete the installation and to allow for a tight, secure ground. To ensure a good ground, scrape away any service...
Operation Manual - Page 8
..., configure your speakers for connecting one or two speakers.
NOTE: Power amplifiers can drive speakers with a nominal impedance range of 12-gauge wire. Power 900/1050
Two Subwoofer
One Subwoofer
SPEAKER OUTPUT
SPEAKER OUTPUT
-- + +
-- + +
SPEAKER OUTPUT
+ LEFT - + RIGHT BRIDGED
MODE
X-OVER
MONO STEREO FULL HPF LPF
Tri-Mode
SPEAKER OUTPUT
+ LEFT - + RIGHT BRIDGED
MODE
X-OVER...
Operation Manual - Page 9
... HPF LPF
+ CH1 + CH3 -
+ CH2 + CH4 - FULL HPF LPF
+ BRIDGED -
4 ohm nominal
7
FULL HPF LPF
+ BRIDGED -
4 ohm nominal 2 ohm minimum
Two Speakers and Bridged Subwoofer
POWER Amplifiers
4 ohm nominal 2 ohm minimum
X-OVER
FULL HPF LPF
+ CH1 + CH3 -
+ CH2 + CH4 - FULL HPF LPF
+ BRIDGED -
4 ohm nominal
Two Subwoofers
4 ohm nominal
X-OVER
FULL HPF...
Operation Manual - Page 10
... Wiring -
Mono Mode
RCA Cable
Power 900/1050
Input Wiring - POWER Amplifiers
Input Wiring
Most trunk/hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat mounting will require a 6-12 foot RCA cable. Stereo Mode
RCA Cable
Input Wiring - Mono Mode
RCA Cable
Input Wiring - Mono Mode
RCA Cable
CAR STEREO / SOURCE UNIT
CAR STEREO...
Operation Manual - Page 11
...-Thru RCA connectors are provided to connect additional amplifiers without the need to purchase "Y" adapters.
9
POWER Amplifiers
Choose a high quality low capacitance cable for the best results. 4 Channel
MODE
234
LINE INPUT
LEVEL BASS EQ HPF
LPF X-OVER
CH1 CH2
CH3
FULL HPF
min ...
LINE OUT
234
NOTE: The use of good quality RCA cables is just as important as power and speaker wire.
Operation Manual - Page 12
...set the crossover to 40Hz, then you would have a 2-channel input from the source unit.
Crossover (X-OVER)
The Jensen Power series of boost.
Power 760 and 920
The 760 and 920 come equiped with a MONO...sonic (sub-sonic) filter at high volumes. See "Input Wiring" on the amplifier is between 60Hz and 80Hz for special applications since improper use a higher crossover setting between...
Operation Manual - Page 13
POWER Amplifiers
Remote Input Level Control
The Power 900 and 1050 come on the receiver, but do not turn up the receiver volume slightly. Testing
Before finishing the installation, perform the following tests to make sure the speakers are connected properly.
The amplifier power light should operate. Turn up the volume. If speakers don't play at amplifier and speakers...
Operation Manual - Page 14
... activated
Input level on amp set too high Amplifier driving 2 ohm load for long durations
Corrective Action Check fuse(s)
Check head unit fuse(s) and wiring Replace fuse and identify cause of failure Replace fuse and identify cause of phase
Check all the power connections are correct, this would indicate an internal problem with
amp
Engine noise /
Ground loop...
Operation Manual - Page 15
... Noise Ratio: 100dBA below reference (Reference: 1 watt, 4-ohms) Additional Power Output: 120 watts RMS X 4 channels into 2-ohms @ < 1% THD+N 190 watts RMS X 2 channels (Bridged Stereo) into 4-ohms @ < 1% THD+N Frequency Response: 10Hz to 60 kHz, -3dB (Reference: 1 watt) Dimensions: L15.75" x H2.5" x W9.0"
Power 1050
Power Output: 290 watts RMS X 1 channels into 4-ohms @ < 1% THD+N Signal to Noise...
Operation Manual - Page 16
POWER Amplifiers
14
Operation Manual - Page 44
... charges for installation, removal or reinstallation of the product • Consequential damage to avoid shipping damage. The Company extends this product or any included plexiglass or lighting (i.e. The Company warrants that provides tracking service to offer you this Warranty, call
1-800-323-4815 for the location of the problem(s) for parts and repair labor. ANY...
Jensen POWER1050 Reviews
We have not received any reviews for Jensen yet.