Operation Manual
Page 4
...Mode Switch (Power 400.2 only) • 2/ 3 / 4 Channel Mode Switch (Power 760.4 only) Power 900.1 • Mono Subwoofer Amp • Low Pass Filter 40 - 240 Hz (Power 900.1) • Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900.1) ...power amplifier is the amplifier of choice for the high demands of amplifiers takes Mobile Hi-Fi to new heights. Like all Jensen products, when it comes to accurate sound reproduction the Power series takes a back seat to change without notice. 2 Jensen will bring your Hi-Fi experience to new heights with 5 Meter Interface Cable Specifications Power 400...
...Mode Switch (Power 400.2 only) • 2/ 3 / 4 Channel Mode Switch (Power 760.4 only) Power 900.1 • Mono Subwoofer Amp • Low Pass Filter 40 - 240 Hz (Power 900.1) • Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900.1) ...power amplifier is the amplifier of choice for the high demands of amplifiers takes Mobile Hi-Fi to new heights. Like all Jensen products, when it comes to accurate sound reproduction the Power series takes a back seat to change without notice. 2 Jensen will bring your Hi-Fi experience to new heights with 5 Meter Interface Cable Specifications Power 400...
Operation Manual
Page 10
...RCA Cable Input Wiring - Mono Mode CAR STEREO / SOURCE UNIT CAR STEREO / SOURCE UNIT Power 760.4 The Power 760.4 can be configured for three different input modes: 2 channel, 3 channel or 4 channel. 2 Channel MODE 234 CH2 CH1 LINE INPUT CH4 CH3CH1&CH2 CONTROLS LEVEL BASS EQ HPF LPF X-OVER...300Hz 40Hz 300Hz FULL LPF HPF LINE OUTPUT 8 Connect an RCA cable from your receiver to the RCA input on your amplifier. Power 400.2 Input Wiring - POWER Amplifiers Input Wiring Most trunk/hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat mounting ...
...RCA Cable Input Wiring - Mono Mode CAR STEREO / SOURCE UNIT CAR STEREO / SOURCE UNIT Power 760.4 The Power 760.4 can be configured for three different input modes: 2 channel, 3 channel or 4 channel. 2 Channel MODE 234 CH2 CH1 LINE INPUT CH4 CH3CH1&CH2 CONTROLS LEVEL BASS EQ HPF LPF X-OVER...300Hz 40Hz 300Hz FULL LPF HPF LINE OUTPUT 8 Connect an RCA cable from your receiver to the RCA input on your amplifier. Power 400.2 Input Wiring - POWER Amplifiers Input Wiring Most trunk/hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat mounting ...
Operation Manual
Page 11
Connecting Additional Amplifiers Pass-Thru RCA connectors are provided to connect additional amplifiers without the need to purchase "Y" adapters. 9 POWER Amplifiers 4 Channel MODE 234 CH2 CH4 CH1 CH3 LINE INPUT LEVEL BASS EQ HPF LPF X-OVER MODE FULL LPF HPF min max 0dB 12dB 40Hz 300Hz 40Hz 300Hz X-OVER 234 min max 0dB 12dB 40Hz 300Hz 40Hz 300Hz FULL LPF HPF LINE OUTPUT NOTE: The use of good quality RCA cables is just as important as power and speaker wire. Choose a high quality low capacitance cable for the best results.
Connecting Additional Amplifiers Pass-Thru RCA connectors are provided to connect additional amplifiers without the need to purchase "Y" adapters. 9 POWER Amplifiers 4 Channel MODE 234 CH2 CH4 CH1 CH3 LINE INPUT LEVEL BASS EQ HPF LPF X-OVER MODE FULL LPF HPF min max 0dB 12dB 40Hz 300Hz 40Hz 300Hz X-OVER 234 min max 0dB 12dB 40Hz 300Hz 40Hz 300Hz FULL LPF HPF LINE OUTPUT NOTE: The use of good quality RCA cables is just as important as power and speaker wire. Choose a high quality low capacitance cable for the best results.
Operation Manual
Page 12
...The Jensen Power series of the Bass Boost could damage your subwoofers at 40Hz, which would have a single input from your subwoofer/enclosure combination. Choose FULL when crossover mode is not active and the amplifier is continuously adjustable from the source unit. Mode Switch Power 400.2 The 400.2 ...distortion, then back it down just a bit. Select LPF (low pass filter) when the amplifier will typically use of amplifiers have a 2-channel input from 0 to +12dB @ 45Hz. On the amplifier, slowly turn the volume up the input level control (clockwise or to the right) until ...
...The Jensen Power series of the Bass Boost could damage your subwoofers at 40Hz, which would have a single input from your subwoofer/enclosure combination. Choose FULL when crossover mode is not active and the amplifier is continuously adjustable from the source unit. Mode Switch Power 400.2 The 400.2 ...distortion, then back it down just a bit. Select LPF (low pass filter) when the amplifier will typically use of amplifiers have a 2-channel input from 0 to +12dB @ 45Hz. On the amplifier, slowly turn the volume up the input level control (clockwise or to the right) until ...
Operation Manual
Page 15
... Power 400.2 Power Output: 60 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 100dBA below reference (Reference: 1 watt, 4-ohms) Additional Power Output: 80 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 160 watts RMS X 1 channels (Bridged Mono) into 4-ohms @ < 1% THD+N Frequency Response: 10Hz to 60 kHz, -3dB (Reference: 1 watt) Dimensions: L 9.5" x H 2.0" x W 8.2" Weight: 4.4 lbs Power 760.4 Power Output: 60 watts RMS X 4 channels...
... Power 400.2 Power Output: 60 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 100dBA below reference (Reference: 1 watt, 4-ohms) Additional Power Output: 80 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 160 watts RMS X 1 channels (Bridged Mono) into 4-ohms @ < 1% THD+N Frequency Response: 10Hz to 60 kHz, -3dB (Reference: 1 watt) Dimensions: L 9.5" x H 2.0" x W 8.2" Weight: 4.4 lbs Power 760.4 Power Output: 60 watts RMS X 4 channels...