Intel SRSH4 - Server Platform - 0 MB RAM Support and Manuals
Get Help and Manuals for this Intel item
Popular Intel SRSH4 Manual Pages
Service Guide - Page 5
... Does Not Light 90 Network Problems ...90 PCI Installation Tips ...91 Problems with Application Software 91 Bootable CD-ROM Is Not Detected 91 Error Messages...92 Error Messages after Power-on 92 POST Error Messages ...93 Beep Codes ...99
A Server Description 100
Feature Summary ...100 Technical specifications ...101 Chassis Access...103 Main Chassis Components 104 Electronics Bay Components...
Service Guide - Page 24
...both a user and an administrator password set, you must enter that came ...Installing the Server in a Rack
The server mounts in the Security section of "N8100-821F NEC Express5800/140Rc-4 User's Guide" (856-121794-502-00) and the instructions that password to power off the system. Install the Rack Mount Kit following the instructions on rack mount kits and the specifications for BIOS Setup...
Service Guide - Page 27
... flat-bladed screwdriver • Antistatic wrist strap and conductive foam pad (recommended) • Pen or pencil • Equipment log (page 131) As you integrate new parts into the system, record the model and serial number of the server system, all installed options, and any other pertinent information specific to the server system.
Service Guide - Page 37
Figure 10. Rotate the handles on the processor board until they are fully open (Figure 10). 2. Removing the Processor Board
Installing and Removing Components
37 Using the handles, tilt the processor board up and remove it from the chassis. Removing the Processor Board
To remove the processor board: 1.
Service Guide - Page 58
... State
Status
Green
Power to slot
58 Status Indicators for installing and removing all eight PCI slots as non-hot-plug slots and follow the instructions on pages 61 and 62 for Hot-Plug PCI Add-In...In that case, you must treat all PCI add-in boards.
Without a driver, the operating system does not support hot-plug installation and removal of the hot-plug PCI add-in boards (Figure 29).
Service Guide - Page 85
... on the front panel to turn the server on the processor board? Are all device drivers properly installed? To check these settings, refer to the operating system documentation. If all cables correctly connected and secured? Check the following:
Are all items are using the system. Are all peripheral devices installed correctly? Are all jumper and switch...
Service Guide - Page 89
...?
Is so, try replacing the corresponding fan module. If you have installed one or more hard drives in use BIOS Setup to make sure that "Onboard Floppy" is on ? Are all relevant switches and jumpers on the hard drive and adapter board set correctly?
Contact your service representative or authorized dealer for assistance.
Diskette Drive Activity...
Service Guide - Page 91
... assistance.
Try a different copy of the software to alter settings so that interrupts are not shared. If the problem persists, contact the software vendor's customer service representative for instructions on the system, contact your vendor about the failing software. PCI Installation Tips
Check the following: Some drivers might be the first bootable device? Make sure all...
Service Guide - Page 99
... action
1. Check if the setting with SETUP is properly installed. 2. Replace the baseboard. 1. Remove the DIMM once, and then re-install it to
check if it operates normally. 3. Check if the DIMM is properly installed. 2. Check if the CPU is properly installed. 2. NOTE: Beep code 1-5-4-2 informs you that the checksum error occurred on ROM. Solving Problems
99 Remove the CPU...
Service Guide - Page 100
... 5.25-inch peripheral bay.
12 GB DDR DRAM memory support. Fault indicators and system UID (Unit ID) light. Ports: USB port 3, RJ45 Serial port B.
Color coded throughout for serviceable items.
Detailed configuration labels on page 17 lists the physical specifications of the server. Six hot-swap system fans in a 1+1 redundant configuration. Table 8.
LEDs: Main power, Standby...
Service Guide - Page 106
...of the EXPRESS5800/140Rc4 server platform. Located behind the bezel door.
106 Release both the front and rear of the chassis, simplifying identification of ...Chassis ID LED
Blue indicates chassis ID is active.
J Fault LED
Red indicates any system fault condition. Located behind the bezel door.
Front Control Panel Features
Device
Operation
A Sleep button
To put a system supporting...
Service Guide - Page 107
...installing a hard disk drive in card slots
Q Chassis ID LED
H Available VHDCI SCSI connector from accessory kit R IEEE-1284 Enhanced Parallel Port
I Available serial port B from accessory kit
Figure 55. Server.... Rear Panel
Figure 55 describes the features of the rear panel of the EXPRESS5800/140Rc-4 server platform. A Power supply AC inlet 1
J
B Power supply AC inlet 2
K
C Optional...
Service Guide - Page 109
... bay comes with six fans in a redundant (5+1) configuration. To ensure that all components remain within specification under all system environmental conditions, do not exceed five minutes for hot swapping of the chassis. System Cooling
CAUTION
All access covers must be on the front panel is set to high.
Server Description
109 The server comes with two...
Service Guide - Page 111
... LVD connectors (P4 and P7)
H ATI Rage XL 2D/3D graphics accelerator J Intel® 82544 Ethernet controller
DD Intelligent Platform Management Bus (IPMB) connector (P12)
K Video RAM (VRAM) (4 MB total)
EE Adaptec 7902 SCSI controller
L Processor board connectors (P21 and P22) FF Fan connector (P11)
M ServerWorks South Bridge Controller (CSB5) GG ServerWorks PCI-X Bus...
Service Guide - Page 120
A power alarm was detected in amber
Description
Action
A thermal error (critical) was detected.
Also make sure that the internal fan cables are firmly connected. Contact your service representative. If this error indication persists, contact your service representative. A fan alarm was detected. A thermal error (warning) was detected.
Identify the failed power supply unit ...
Intel SRSH4 Reviews
We have not received any reviews for Intel yet.