Icom M85 / M85UL IS Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom M85 / M85UL IS manuals!
Problems with Icom M85 / M85UL IS?
Ask a Question
Free Icom M85 / M85UL IS manuals!
Problems with Icom M85 / M85UL IS?
Ask a Question
Popular Icom M85 / M85UL IS Manual Pages
M85 - Instruction Manual - Page 2
... is cracked or broken, or the transceiver has been dropped.
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely before operating. SAVE THIS INSTRUCTION MANUAL - USING CHANNEL 16 DISTRESS CALL PROCEDURE 1. EXPLICIT DEFINITIONS
RECOMMENDATION
WORD
DEFINITION
RDANGER!
Contact your Icom distributor or your position). 5. State the nature of the art technology and...
M85 - Instruction Manual - Page 3
... a headset
••Force majeure, including, but also the transceiver. Only Icom battery packs are very loud. Even if the volume level is set low, the beeps of the
very close to, or touching exposed parts of the specified temperature range:
IC-M85:
-30°C (-22˚F) ~ +60°C (+140˚F)
IC-M85E:
-25...
M85 - Instruction Manual - Page 10
...!1 !0
o w
e
i
u
r
y
t
Microphone
Speaker
q LOCK KEY [ ]
Hold down for 1 second to set or clear the selected channel as a Favorite channel. i WEATHER CHANNEL*/ CHANNEL GROUP KEY [CH/WX]/[U/I/C/L]/[CH] zzPush to..., or when the squelch is open the squelch, to start , depending on the Set mode settings. LLPush to enter or exit the Weather Channel Selection mode.* (p. 12)
*Except ...
M85 - Instruction Manual - Page 17
...
8
1. The transceiver automatically detects a Weather Alert tone
4
on the transceiver version. Turn OFF the transceiver.
9
2. While holding down [U/I/C/L]*1 or [CH]*2 for 1 second to exit the Set
14
mode.
15
Weather channel list
16
Channel Frequency (MHz) Channel Frequency (MHz)
1
162.550
6
162.500
2
162.400
7
162.525
3
162.475
8
161...
M85 - Instruction Manual - Page 18
...PTT] to exit the ATIS Code Entry mode. Turn OFF the transceiver. 2. While holding down [PTT], and speak into the microphone to the left. 4. LLRotate [DIAL] to set the ID. 5. LLPush [SCAN... after 5
minutes* of 10 digits. Release to receive.
■■Entering the ATIS code
(For the German and Dutch versions)
The Automatic Transmitter Identification System (ATIS) ID consists of...
M85 - Instruction Manual - Page 19
... the function.
11
■■Using the VOX function
TIP: When the AquaQuake Action setting is ON in the speaker grill may muffle the sound coming from the speaker grill by... low frequency vibration beep sounds for 10 seconds to drain the water, regardless of the volume level setting.
10
3. BASIC OPERATION 5
■■Adjusting the squelch level
■■Using the AquaQuake ...
M85 - Instruction Manual - Page 20
....
15 LLOnly the Favorite channels are scanned. ••Turn ON the Priority Scan in the Set mode to scan as a Favorite channel. 6 SCAN (Except the Dutch version)
■■Scan... Priority scan sequentially scans all Favorite channels.
Before starting a scan, you need to: ••Set the channels that you want to use the
Priority Scan (p. 20).
CH 01
CH 02
WX*
...
M85 - Instruction Manual - Page 21
...2
••During a Normal scan, "SCAN" blinks.
3
••During a Priority scan, " " is received.
16
DDSetting/Clearing
1.
Push [SCAN] to properly receive signals, be set as Favorite channels. Status indicator lights green when a signal is also displayed.
Example: Starting a Normal Scan
SCAN OPERATION 6
■■Starting a scan
1
1.
LLIf there ...
M85 - Instruction Manual - Page 22
...
call channel. 4. Push [DUAL] again to start Dualwatch or
Tri-watch. ••During Dualwatch, "DUAL 16" blinks. ••During Tri-watch in the Set mode (p. 20). 2. When a signal is received on the Channel 16.
17 LLA beep tone sounds when a signal is received on Channel 16.
Dualwatch resumes after...
M85 - Instruction Manual - Page 23
... the supplied battery pack, you must activate the scrambler function. Ask your local Icom dealer for the LAND channel group setting and LMR/PMR
zzHold down [H/L] for 1 second to display the battery ...the function.
••"SCRM" is not usable on Channel 16. In
15
order to set the
16
scrambler code in the VHF band. 8 OTHER FUNCTIONS
■■Using the LAND channel group ■...
M85 - Instruction Manual - Page 24
... Display*3
••Scrambler Code
••VOX Level
••VOX Delay
••AquaQuake Action
••Man Down Alarm
••Lone Worker Alarm ••Auto Volume Up
••MOB Alarm
19 Rotate [DIAL] to select an item. 4. Push [16/C] to
enter the Set mode. ••...
M85 - Instruction Manual - Page 25
...
Selects the watch type.
16
••d- (Dual): The watch type is set to Dualwatch, which
monitors Channel 16, even while receiving a
signal on another channel.
••t- (Tri):... The watch type is set to Tri-watch, which sequentially
searches all Favorite channels in the channel group, while also periodically...
M85 - Instruction Manual - Page 26
... Code " "
Set the voice scrambler code to between 1 (The lowest sensitivity) to Low. You can select settings for 5 seconds when the user
pushes any key.
The VOX Delay is set ...to 10 (The highest sensitivity).
DDPower Save " "
Turns the Power Save function ON or OFF. ••OFF: The function is activated by
deactivating the receiver circuit of the transceiver at specific...
M85 - Instruction Manual - Page 27
DDMan Down Alarm " "
Sets the emergency mode detection angle to stop the alarm.
4
*An alarm sounds from the transceiver's speaker, even.... ••ON: You can use the function by shaking the transceiver.
If the transceiver leans past the set angle for the Man Down Alarm function. SET MODE 9
DDLone Worker Alarm " "
1
Turns the Lone Worker Alarm ON or OFF.
2
If no operation ...
M85 - Instruction Manual - Page 34
...H old down [ ] for low power or receive only by regulations.
• The output power is set . • S et the Favorite channels.
• The Key Beep function is exhausted.
• ...set for 1 second to select high power. REF. not turn ON.
• The battery pack is locked. p. 9 p. 3 p. 14 p. 5 p. 14
p. 11
p. 5 p. 16 p. 20 p. 5
29 Scan does not start.
12 TROUBLESHOOTING
PROBLEM...
Icom M85 / M85UL IS Reviews
We have not received any reviews for Icom yet.