Icom IC-FR9020 Support and Manuals
Get Help and Manuals for this Icom item
This item is in your list!
View All Support Options Below
Free Icom IC-FR9020 manuals!
Problems with Icom IC-FR9020?
Ask a Question
Free Icom IC-FR9020 manuals!
Problems with Icom IC-FR9020?
Ask a Question
Popular Icom IC-FR9020 Manual Pages
Instruction Manual - Page 1
Operation is subject to the condition that this device does not cause harmful interference. INSTRUCTION MANUAL
VHF P25 REPEATER
iFR9010
UHF P25 REPEATER
iFR9020
This device complies with Part 15 of the FCC Rules.
Instruction Manual - Page 2
... into the design of trouble-free operation. This manual covers up to operate the repeater. jects touch any internal part or connectors on the repeater rear panel. The antenna (s) used for extended periods. The peak conducted output power at any liquids.
READ THIS INSTRUCTION MANUAL carefully and completely before attempting to firmware version 71MDV024 and DSPV326...
Instruction Manual - Page 3
... convert the Object Code into a human readable form. Icom, Icom Inc, and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other products or brands are fully aware of the hazards, and the ways to comply with the instruction manual, may also...
Instruction Manual - Page 5
... UPDATE 4 8.7 STATUS REQUEST 4 8.8 PREDEFINED MESSAGES 5 8.9 RADIO MONITOR 5 8.10 SBC LOG 5 9 P25 SQUELCH ADJUSTMENT 5 10 TALKGROUP ALIAS ID 5 11 KEY-LOCK 6 12 MANUAL ...FIRMWARE VERSIONS........ 9 25 DISPLAYING THE SERIAL NUMBER 9
26 DISPLAYING THE PROGRAMMING SOFTWARE VERSION 9
27 DATA CHECK 9 28 ERROR MESSAGES 9 29 FIRMWARE ERROR DETECTION 9 30 RS-232 ERROR DETECTION 10 31 DSP ERROR...
Instruction Manual - Page 6
... = Indicates Analog channel data [8] = Key lock ON/OFF [9] = No function [A] = Manual CWID send key [B] = Programmed CWID Start/Stop key [C] = Cryptogram Test [D] = No ... call number
[C] = TX Transmit mode (Clear or Secure), only models with encryption
[D] = P25 mode (analog or digital TX) [Q] =...The LED flashes when an error on .
2 LED DISPLAY
The IC-FR9010/FR9020 has 5 LED's from left to normal ...
Instruction Manual - Page 7
...from 0 to 30 seconds. RX TX
C001 Figure 4
TAC 2
MD N
Light - 15
5 CHANNEL SELECTION
The IC-FR9010/FR9020 has capability of up to adjust the Backlight Timer. Push [CH], and then enter the channel number.
RX TX... been turned ON with [SHIFT] + [1] (backlight ON/OFF). Figure 4 shows the Backlight Timer set for ID entry.)
RX TX
C001 GPC 00001
Figure 5 RX TX
TAC 2
MD N
C001
TAC ...
Instruction Manual - Page 8
... IDC 12345
Figure 9
TAC 2
MD N
7 P25 PTT MODE
Push [D] to work with any P25 radio under the TIA specifications. When the display shows PTT is pushed. Figure 9 shows completed entry, [1] + [2] + [3] + [4] + [5] + [B].
The IC-FR9010/FR9020 has been developed to select PTT (Push-To-Talk) mode.
Emergency calls can receive Group calls, All Call and...
Instruction Manual - Page 9
... display. The status numbers relates to enable a subscriber unit that has been disabled, the password must match the password entered in the BTIII program for inhibit to occur.
8.6 STATUS UPDATE
Used to disable a subscriber unit (mobile or portable). Status Update To: 366
USR: 1
UNT: 0
MD N
Figure 16
To inhibit a radio, push [F] then push [A] or...
Instruction Manual - Page 11
...manually send the programmed CWID. This symbol shows on the pre-setting, this information cannot be locked, select DISABLE in TX 6) TX RX Modulation type either reboot the radio or push [SHIFT] + hold [B] for 2 seconds. (CWID must be enabled in programming to show the TGID. Figure 24 shows Key locked.
CWID sending Code: ICOM... disables both programmed and manual CWID.) To return to...
Instruction Manual - Page 12
... on line 1 indicates Receive Channel.
If the radio is Narrow band.
Status Update RCV
4. Radio Monitor RCV
7.
"D" = Duplex and "R" = Repeat Line ...TOGGLE
By Default, the Backlight illuminates for backlight timer settings. Figure 33 Indicates the Backlight is ON.
The...34
19 CALLER ID
MD N
In Simplex mode the IC-FR9010/FR9020 display indicates the source Unit ID or Individual ID....
Instruction Manual - Page 13
...channel.
23 REMOTE CONTROL
IC-FR9010/FR9020 can be controlled remotely ...carrier frequency and CTCSS/DCS.
21.2 DIGITAL
Matching NAC (Network Access Code); If the programmed NAC matches the received NAC it transmits digital...The 3rd line shows E001 instead of C001. (EXXX means remote, CXXX is set for Channel control pinouts and other related information. Local operation is received. Figure...
Instruction Manual - Page 14
.... Set by p-kgprg 023195 Figure 42
27 DATA CHECK
The IC-FR9010/FR9020 has a self diagnostic function. Figure 45 displays a TX PLL error.... 39 displays Radio and DSP Firmware versions. 24 DISPLAYING THE FIRMWARE VERSIONS
Both the radio and DSP firmware versions are open or a... If the data is indicated. EEROM Data Error Figure 43
28 ERROR MESSAGES
If there is a problem with the RX PLL, TX PLL or...
Instruction Manual - Page 15
...installed correctly, and the correct firmware version is a problem with the DSP, the following messages are shown on the display. Figure 49 shows DSP serial error....Error Figure 49
10 30 RS-232 ERROR DETECTION
If the communications between PC and the repeater have trouble, the following message may be shown on the LCD. - Overrun error - Framing error -
Receive timeout
31 DSP ERROR...
Instruction Manual - Page 16
...
O 0 to +3.3 V DC +3.3 V = busy
Receive signal strength
O 0 to +2.5 V DC
indicator
analog
External audio modulation input l ≈50 mVrms
1 kHz
for ±3 kHz i.e. The functions of IC-FR9010/FR9020. Name 1 CH 0 2 CH 1 3 CH 2 4 CH 3 5 Unassigned 6 REM MON 7 GND 8 Unassigned 9 REM D/A 10 DEM OUT
11 BUSY 12 RSSI 13 MOD1
14 GND 15 PTT 16...
Icom IC-FR9020 Reviews
Do you have an experience with the Icom IC-FR9020 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!