Icom IC-FR9010 Series Support and Manuals
Get Help and Manuals for this Icom item
This item is in your list!
View All Support Options Below
Free Icom IC-FR9010 Series manuals!
Problems with Icom IC-FR9010 Series?
Ask a Question
Free Icom IC-FR9010 Series manuals!
Problems with Icom IC-FR9010 Series?
Ask a Question
Popular Icom IC-FR9010 Series Manual Pages
Instruction Manual - Page 1
Operation is subject to the condition that this device does not cause harmful interference. INSTRUCTION MANUAL
VHF P25 REPEATER
iFR9010
UHF P25 REPEATER
iFR9020
This device complies with Part 15 of the FCC Rules.
Instruction Manual - Page 2
... Icom's philosophy of trouble-free operation. R WARNING HIGH VOLTAGE! This may result in a secure place to thank you for making the The IC-FR9010/FR9020 your IC-FR9010/FR9020.
Place the repeater in an electrical shock or burn.
FORWARD
Thank you for purchasing this trans- The IC-FR9010/ FR9020 vhf/uhf p25 repeaters are met. (See FCC Rules Part...
Instruction Manual - Page 3
...if not installed and ... antenna specifically authorized by...IC RF exposure limits for Safety Levels with this Communications Equipment.
Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can cause FCC and IC...instruction manual, may also cause you to part 15 of the hazards, and the ways to do so. U.S.
This voice coding...
Instruction Manual - Page 5
... UPDATE 4 8.7 STATUS REQUEST 4 8.8 PREDEFINED MESSAGES 5 8.9 RADIO MONITOR 5 8.10 SBC LOG 5 9 P25 SQUELCH ADJUSTMENT 5 10 TALKGROUP ALIAS ID 5 11 KEY-LOCK 6 12 MANUAL ...FIRMWARE VERSIONS....... 9 25 DISPLAYING THE SERIAL NUMBER 9
26 DISPLAYING THE PROGRAMMING SOFTWARE VERSION 9
27 DATA CHECK 9 28 ERROR MESSAGES 9 29 FIRMWARE ERROR DETECTION 9 30 RS-232 ERROR DETECTION 10 31 DSP ERROR...
Instruction Manual - Page 6
...), only models with encryption...Manual CWID send key [B] = Programmed CWID Start/Stop key [C] = Cryptogram Test [D] = No function [Q] = Indicating P25 data (while de- P25 squelch: N = Normal squelch S = Selective squelch e. quencies [F] (Scan) = SBC (Conventional Control Messag- Key lock mode: = Key lock (Not displayed if in repeat mode (The IC-FR9010...error on .
2 LED DISPLAY
The IC-FR9010...
Instruction Manual - Page 7
...unit ID on the same NAC. RX TX
C001 Figure 4
TAC 2
MD N
Light - 15
5 CHANNEL SELECTION
The IC-FR9010/FR9020 has capability of up to scroll through the menu. Push [CH] + [5] + [0] + [0]
6 P25 ...the backlight has been turned ON with [SHIFT] + [1] (backlight ON/OFF). Figure 4 shows the Backlight Timer set for ID entry.)
RX TX
C001 GPC 00001
Figure 5 RX TX
TAC 2
MD N
C001
TAC 2
GPC ...
Instruction Manual - Page 8
...
Figure 8 RX TX
TAC 2
MD N
C001 IDC 12345
Figure 9
TAC 2
MD N
7 P25 PTT MODE
Push [D] to work with any P25 radio under the TIA specifications. The IC-FR9010/FR9020 has been developed to select PTT (Push-To-Talk) mode. EMERGENCY MODE RX To clear a received Emergency call, push and release [F] twice. Push [F] to...
Instruction Manual - Page 9
.... Radio Check To: _
MD N Fm: 00000366 (ACK)
Figure 13
8.4 RADIO INHIBIT
This function is displayed and enter the target radio's ID, enter the password and then push [#]. Status Update To: 366
USR: 1
UNT: 0
MD N
Figure 16
To inhibit a radio, push [F] then push [A] or [B] until the selection is displayed then enter the target...
Instruction Manual - Page 11
...be locked, select DISABLE in the programming software. This symbol shows on the pre-setting, this information cannot be depressed to use these functions.) Figure 26 shows CWID ... + hold [B] for 2 seconds. (This disables both programmed and manual CWID.) To return to normal operation, either PM or FM (PM is locked. CWID sending Code: ICOM
C001
TAC 2
MD N
RX TX
C001
TAC 2
CWID function ...
Instruction Manual - Page 12
... TOGGLE
By Default, the Backlight illuminates for backlight timer settings. Push [SHIFT] + [1] again to return to ... 00001
Figure 34
19 CALLER ID
MD N
In Simplex mode the IC-FR9010/FR9020 display indicates the source Unit ID or Individual ID. Figure 31... (IDC)
Figure 36
MD N
7 Radio Uninhibit RCV
3. Status Update RCV
4. Radio Monitor RCV
7. The 3rd character indicates Wide band....
Instruction Manual - Page 13
...in RX NAC w/Through OFF; If the RX NAC is set for Channel control pinouts and other related information. The [MON...radio to the chart on an individual channel.
23 REMOTE CONTROL
IC-FR9010/FR9020 can be controlled remotely by pulling pin 24 of the... frequency and CTCSS/DCS.
21.2 DIGITAL
Matching NAC (Network Access Code); If the programmed NAC matches the received NAC it transmits digital...
Instruction Manual - Page 14
...FIRMWARE ERROR DETECTION
When the radio itself detects a malfunction, the main CPU will reboot in the normal mode.
If the data is released, the radio will reboot in the normal mode. Figure 43 shows ERROM Data error. Set by p-kgprg 023195 Figure 42
27 DATA CHECK
The IC-FR9010... V-0.2.3195 version.
EEROM Data Error Figure 43
28 ERROR MESSAGES
If there is a problem with the RX PLL, TX...
Instruction Manual - Page 15
... RS-232 ERROR DETECTION
If the communications between PC and the repeater have trouble, the following message may be shown on the LCD. - Data unmatched - Figure 47 shows DSP failure. Figure 48 shows DSP not ready. Please check that the DSP board is installed correctly, and the correct firmware version is a problem with the DSP...
Instruction Manual - Page 16
... +3.3 V DC
l 0 to +3.3 V DC
l 0 to +3.3 V DC 0 V = transmit
External modulation input
l ≈400 mVrms After limiter and filtering/LOW
1 kHz
FREQ
for ±3 kHz i.e. The functions of IC-FR9010/FR9020. 32 OPTION PORT PINOUT
25 pin D-sub connector for more information on display indications.
11
Icom IC-FR9010 Series Reviews
Do you have an experience with the Icom IC-FR9010 Series that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!