Icom IC-F43TR Support and Manuals
Get Help and Manuals for this Icom item
This item is in your list!
View All Support Options Below
Free Icom IC-F43TR manuals!
Problems with Icom IC-F43TR?
Ask a Question
Free Icom IC-F43TR manuals!
Problems with Icom IC-F43TR?
Ask a Question
Popular Icom IC-F43TR Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
UHF TRUNKED RADIO
iF43TR
(LTR®/Passport version)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
Instruction Manual - Page 2
... charge only specified Icom battery
packs with Icom chargers. Only Icom battery packs are tested and approved for the IC-F43TR UHF TRUNKED RADIO. CAUTION NOTE
DEFINITION Personal death, serious injury or an explosion may occur. Equipment damage may occur.
R WARNING! LTR® is a registered trademark of personal injury, fire or electric shock. All other audio accessories at high...
Instruction Manual - Page 3
... modifications to this transceiver, not expressly approved by unauthorized modification. KEEP the transceiver away from the heavy rain, and Never
immerse it continuously for any problems caused by Icom Inc., could void your authority to transmit. CAUTION: MAKE SURE the flexible antenna and bat-
Instruction Manual - Page 8
... select the talk group on the pre-setting)
Push to mute and release the CTCSS (DTCS) squelch mute. release to receive.
Selects the pre-programmed system channels or talk
!0 MONITOR KEY
...
o PTT SWITCH [PTT]
q ROTARY SELECTOR
Push and hold to [P3]
Desired functions can be programmed independently by
i
t
your dealer. Turns power ON and adjusts the audio level.
!1 ANTENNA CONNECTOR
e...
Instruction Manual - Page 10
... programming.
Scanning resumes after passing
a specified time period specified. Scanning resumes after pass- SCAN B KEY
PRIORITY KEY
➥ P ush to pause scanning.
mit a DTMF emergency call mute function ON.
➥ P ush and hold to turn the DTMF select call code. 2 PANEL DESCRIPTION
■ Programmable function keys
The following explanations, the specific...
Instruction Manual - Page 15
...; If an error beep is out of the communication area, " " disappears, and "NO SVC" message appears. a DTMF encode channel appears. D Phone call )
-Optional UT-108 is pre-programmed. After a while, repeat step w again. • T he beep can be turned OFF in User set mode. • W hen the transceiver is emitted, release [PTT]. code channel...
Instruction Manual - Page 21
... scrambler function OFF. • " " disappears.
■ Stun function
When the specified code, set as a stun code, is installed, the Man Down function can be available. To use the transceiver, extend the running time.... If you want to turn the Run Time Limit function OFF using the CS-F43TR cloning software.
■ Man Down transmission
When the optional UT-124 man down emergency call...
Instruction Manual - Page 24
... seawater, or any other damage, the cells inside the battery gets in your eyes with Icom radios or Icom charger. High temperature buildup in the battery, such as could occur near fires or stoves, inside...surface of the battery does not show cracks or any purpose that is not specified in this instruction manual.
• R DANGER! Misuse can result. Do not use a wet battery. Excessive ...
Service Manual - Page 2
... used for the IC-F43TR UHF TRUNKED RADIO at the time of test equipment thoroughly before disassembling the transceiver. 2. DO NOT open the transceiver until the transceiver is internal before connecting equipment to include the following four points when ordering replacement parts:
1. 10-digit order numbers 2.
INTRODUCTION
This service manual describes the latest service information for...
Service Manual - Page 11
...The output signal is applied to the
APC amplifier (IC16, pin 1).
• BASE BAND IC BLOCK DIAGRAM
TXINO 4
TXIN 3 TXA1
VR1 (HPF)
RXINO 22
Compressor
Preemphasis
TX/RX HPF
...then applied to compress the audio signals. 4-5 OTHER CIRCUITS
4-5-1 COMPOUNDER CIRCUIT (MAIN UNIT) IC-F43TR have compounder circuit which can improve S/N ratio and become wide dynamic range to suppress the ...
Service Manual - Page 13
... into the appropriate CD
drive. Otherwise, the transceiver can not start software adjustment. F43TR ADJ' in the U.S.A. I ADJUSTMENT SOFTWARE INSTALLATION q Boot up Windows, and click the program group 'CS- SECTION 5 ADJUSTMENT PROCEDURES
5-1 PREPARATION
When adjusting IC-F43TR, the optional CS-F43TR ADJ ADJUSTMENT SOFTWARE (Rev. 1.0 or later), OPC-478 CLONING CABLE and a JIG CABLE (see...
Service Manual - Page 14
Each transceiver has its own specific values for each setting.
1 : Transceiver's connection ... for TX (automatically) 17 : PLL lock voltage for RX (manually) 18 : PLL lock voltage for settings are example only. • SCREEN DISPLAY EXAMPLE
CS-F43TR ADJ Rev.1.0
File Option
2
COM 1: OPEN
Connect
Reload (F5...MHz
485.000 MHz
CTCSS DTCS code
: 151.4 Hz : 007
Band width : Wide
6
470.000 MHz
520...
Service Manual - Page 15
...; CONNECTION
Standard signal generator 0.1 µV to 32 mV
(-127 dBm to -17 dBm)
to RS-232C port
To [SP] JIG cable
SINAD meter Speaker (8 Ω)
IC-F43TR (10-keypad version)
• JIG CABLE
To IC-F43TR [SP] jack
3-conductor 3.5(d) mm plug JIG cable
( -
Service Manual - Page 17
... freq. : CH2
Push the [ENTER] key on the adjustment program and then push [ENTER] key. panel
nector and set as :
Push the [ENTER] key on the connected computer keyboard...CONVENIENT:
The BPF T1, BPF T2 can be adjusted properly. SOFTWARE ADJUSTMENT (RECEIVING)
• Select an operation using keys, then set specified value using keys on the connected computer keyboard
Level
: 0....
Icom IC-F43TR Reviews
Do you have an experience with the Icom IC-F43TR that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!