Icom F70D / F80D Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom F70D / F80D manuals!
Problems with Icom F70D / F80D?
Ask a Question
Free Icom F70D / F80D manuals!
Problems with Icom F70D / F80D?
Ask a Question
Popular Icom F70D / F80D Manual Pages
Instruction Manual - Page 2
SAVE THIS INSTRUCTION MANUAL -
If disregarded, inconvenience only. ABOUT FM APPROVED
Versions of the IC-F70/F80 which display the "FM APPROVED" symbol as at left on the serial number seal, conform to decompile, reverse engineer, or disassemble the Object Code, or in this Technology is licensed solely for details concerning your Icom dealer or...
Instruction Manual - Page 3
... accessories at authorized Icom service center only. operate this transceiver, not
+60°C (+140°F).
tenna is not manufactured or approved by Icom Inc., could void... microphone is 5 to 10 cm (2 to , or touching exposed parts of Icom Incor-
The IC-F70/F80 series transceivers
employ waterproof construction, which ...installation should be operate
Icom, Icom Inc. CAUTION!
Instruction Manual - Page 10
...CODE MEMORY INDICATOR Appears when the call code memory is activated. Ask your dealer for details. • In this instruction manual, the LCD illustration is selected.
o ALPHANUMERIC DISPLAY ➥ Displays an operating channel number, channel name, Set mode contents, DTMF code... INDICATOR Appears/blinks when the specific 2/5-tone/MDC 1200 code is received, according to a specified...
Instruction Manual - Page 11
...specific key is used to activate the function depends on the Power ON Scan setting.
ZONE KEY "ZONE" Push this key for grouping.
Scanning resumes after pushing and holding
[Scan A Start/Stop]/[Scan B Start/Stop]. ➥ P ush to pause scanning. Consult your Icom...operating channel. ➥ P ush to select a transmit code channel after the transmission is finished. ➥ Push ...
Instruction Manual - Page 12
... or 20.0 kHz
using [CH Up]/ [CH Down] to change the tone frequency/code setting. to transmit the last-transmitted DTMF code.
TALK AROUND KEY "TA" Push to 'Audible' only). LOCK KEY "LOCK...DTMR"
when the backlight function is turned OFF in user set as the continuous tone channel until another channel is finished to send a 'reset code'.
NOTE: The un-mute condition ('Audible' condition) ...
Instruction Manual - Page 13
... station depend-
ID-MR SELECT KEY "IDMS" (PMR operation only) ➥ Recalls detected ID codes.
13
SURVEILLANCE KEY "SURV"
• Push this key, then select the ID code using [CH Up]/[CH Down].
6
ing on the pre-setting. set the desired channel using [CH Up]/[CH Down].
14
Push to erase the selected ID...
Instruction Manual - Page 14
...the
continuous tone channel using [CH Up] or [CH Down] to change the tone frequency/code setting. ➥ While in the digital mode operation, push to select the NAC channel using [CH Up] ...connector. Then push this key to change the NAC code setting. USER SET MODE KEY "SET" ➥ P ush and hold to enter user set mode.
• D uring user set mode, push this key to select an item, ...
Instruction Manual - Page 16
... the desired operating channel, in sequence;
Therefore "01234" and "56789" are available. Turn the power off and start up password,
input the digit codes as directed by your system set up.
AUTOMATIC SCAN TYPE: Channel setting is programmed for a start over in this type. Methods may be incorrect. Scanning stops when receiving a call.
12...
Instruction Manual - Page 17
...5 to 10 cm (2 to 4 inches) from contacting you to call specific station(s) only
w Push [CH Up] or [CH Down], or...audio output level to a comfortable listening level.
6
System Operator's instructions.
7
• This may not be necessary depending on programming...on the pre-setting.
5
q Select the desired TX code channel, 2/5-tone code, Individual ID code* or Talkgroup ID code* according to...
Instruction Manual - Page 18
... function The transceiver has several inhibit functions which restrict transmission under the following conditions:
- The channel is received.*
(Depending on the pre-setting.) - Un-matched (or matched) NAC is in mute condition ('Inaudible' condition; When the TX code channel number (or name) is activated, causing the transceiver to select the desired TX...
Instruction Manual - Page 19
... SELECT] KEY:
q Select the desired TX code channel via [TX Code CH
3
Select]+[CH Up] or [CH Down], [TX Code CH Up] or [TX Code CH Down].
4
q Push [TX Code CH Select] to enter the TX code channel
w Push [TX Code Enter] to set the desired
blink automatically without pushing [TX Code CH Select]. to enter the
• The...
Instruction Manual - Page 20
... it , the indication can be toggled between the operating channel number (or name) and Talkgroup ID code (or name). cancels the selected Individual ID code
(return to the pre-set Talkgroup ID code in the channel.)
D Talkgroup ID code selection
(Digital mode operation only) If the transceiver has [Talkgroup] assigned to it, the indication can...
Instruction Manual - Page 21
..., Vox Gain*, Vox Delay*, Battery
6 7
[P0] to p. 10 [User
14
Set Mode] section.
15
16
17
Then, push
3
ize" the transceiver operation to suit your preferences and operating ...style.
[Up] or [Down] to set the desired
level/condition.
[Up]
4
• Available set mode functions are [Down]
5
Entering the user set mode:
Backlight, LCD Contrast, Beep,
q While pushing ...
Instruction Manual - Page 23
...Icom radios or Icom chargers. Misuse can result.
Do not use a battery with any purpose that is specified. Never use the battery if it has been severely impacted or dropped, or if the battery has been subjected to wipe it is not specified in this instruction manual...or stoves, inside the battery gets in areas with Icom radios or Icom chargers. DO NOT expose the battery to rain, ...
Instruction Manual - Page 25
... on version) or the DC power cable (OPC-515L/CP-17L).
D AD-110 installation
The AD-110 charger adapter must be used instead of the AC adapter. Optional OPC-... 13 14 15 16
21 BATTERY CHARGING 4
■ Optional battery chargers
NOTE: See each instruction manual for 12 V cigarette lighter socket) can be installed into the BC119N or BC-121N before battery charging. ➥ C onnect the AD-110...
Icom F70D / F80D Reviews
We have not received any reviews for Icom yet.