Icom F5011 / F6011 Support and Manuals
Get Help and Manuals for this Icom item
This item is in your list!
View All Support Options Below
Free Icom F5011 / F6011 manuals!
Problems with Icom F5011 / F6011?
Ask a Question
Free Icom F5011 / F6011 manuals!
Problems with Icom F5011 / F6011?
Ask a Question
Popular Icom F5011 / F6011 Manual Pages
Instruction Manual - Page 2
... part 15 of personal injury, fire or electric shock. These limits are designed to provide reasonable protection against harmful interference when the equipment is likely to operate this transceiver,
not expressly approved by Icom Inc., could void your authority to cause harmful interference in a commercial environment. Icom, Icom Inc. All other countries. SAVE THIS INSTRUCTION MANUAL...
Instruction Manual - Page 3
.... BE CAREFUL! R WARNING! The vehicle's battery will ob-
peratures below -30°C (-22°F) or above +60°C (+140°F), or in the event the Icom transceiver is used with equipment that is not responsible for optimal performance when used with tem- NEVER cut the DC power cable be- This could...
Instruction Manual - Page 4
... ON the power 7 ■ Channel selection 7 ■ Call procedure 8 ■ Receiving and transmitting 8 ■ User Set mode 10 ■ Scrambler function 11 ■ Stun function 11 ■ Priority A channel selection 11 ■ Emergency transmission ...15 ■ Antenna 16 ■ Fuse replacement 16 ■ Cleaning 16 ■ Options 16
4 SAFETY TRAINING INFORMATION 17-19
iii
Instruction Manual - Page 5
... audio output level. Password prompt
14
NEVER connect non-specified microphones. 1 PANEL DESCRIPTION
■ Front panel
1
q
Function LED (p. 2)
Speaker
2
3
4
1
2
3
4
5
TX/RX
6
7
P0 P1 P2 P3
8
9
w
e
r
10
11
q AF VOLUME CONTROL KNOB [VOL] Rotate the knob to turn the power ON or OFF.
12
• Minimum audio level is pre-set. (p. 10)
•...
Instruction Manual - Page 6
... ➥ Blinks when receiving a signal during a scan. ➥ All LEDs blink while entering the power ON password.
e ACTIVATED KEY INDICATORS (P0/P1/P2) Lights when a pre-programmed key function is activated.
NOTE: When...when a cloning error has occurred. Scan is paused when you take it OFF hook - Automatically selects the Priority A channel when you take it OFF
hook. - Sets to 'Audible...
Instruction Manual - Page 7
...cancel a scan, depend- Push to mute the channel (Inaudible mode). - Push to send a 'reset code' after the scan is cancelled except by a detected signal, on a channel other than a priority channel,... push this key for 1 second to start or cancel a scan. Consult your Icom dealer or system operator for details con-
➥ Push to select Priority Channel A or B. ➥...
Instruction Manual - Page 9
...the surveillance function ON or OFF.
➥ Hold down for 1 second again to exit the User Set
SIREN
mode. This function can only be used for situations other than an emergency alert, such as ... the function.
5
When this function is turned ON, the beeps do not sound
• During User Set mode, push this key again to select an item*, and
the LED does not light when a signal is...
Instruction Manual - Page 11
...-CH 1] to [MR-CH 4] keys to select a channel directly.
5
6
KEY
P0 P1 P2 P3
AUTOMATIC SCAN TYPE: Channel setting is programmed for a start up password,
differ, according to your system set up.
3
input the digit codes as identical. 2 BASIC OPERATION
■ Turning ON the power
■ Channel selection
1
q Push [ ] to turn -
7
NUMBER 0
1
2
3
4
56789
ing...
Instruction Manual - Page 14
... [P3] to select the appropriate item.
Entering the User Set mode: q H old down [User Set Mode] for 1 second again to exit
the User Set mode. 10 When the minimum value or "OFF" is selected, an error beep sounds if [P2] is pushed. e P ush and hold [User Set Mode] for 1 second to enter the User
Item...
Instruction Manual - Page 16
... call operation. IMPORTANT: It is transmitted on the operating channel.
D NOTES
Depending on the preprogramming, receiving a matching 5-tone code cancels the transmission.
When no emergency channel is specified, the call is recommended to set an emergency channel individually to cancel the Emergency function, hold down for the specified time period*, the emergency...
Instruction Manual - Page 19
...9632; Supplied Accessories
Microphone
Microphone hanger Microphone
and screw set
hanger cable
DC power cable
Function name stickers*
...ceiver also allows overhead mounting.
3
• Mount the transceiver securely with the 4 supplied screws
to a thick surface which can support more than 1.5 kg
4
(3.3 lb).
5
Flat washer
6
7
8
9
Felt*
10
Spring washer
11
12
13
14
15
...
Instruction Manual - Page 20
...of any communication systems is installed in the performance of the problem if possible, repaire it clean with a new...code squelch capabilities. faces. 16
input power: 7 W (SP-22/SP-35)/30W (SP-30)
SP-22/SP-35 : Compact and easy-to install...ft)
■ Fuse replacement
A fuse is the antenna. If the transceiver becomes dusty or dirty, wipe it and then replace the damaged fuse with...
Instruction Manual - Page 21
... two conditions:
the properly installed antenna. 4 SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during the course of employment by the "General Popula- IC-F6011/IC-F6013H:
14
The...use by individuals aware of the hazards, and the ways to bystanders. 2. IC-F5011/IC-F5013H: Transmit only when people outside of 37 centimeters or more between the ...
Instruction Manual - Page 24
A-6902H-1EX-w Printed in Japan © 2010-2012 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Analog Mobiles Comparison Chart - Page 1
... other trademarks remain the property of Icom Inc. AT-A-GLANCE
Analog Mobile Radio Comparison
F5011
Entry level analog mobile
F5021
Mid...(VHF)
• Full analog signaling (2/5 tone, MDC1200)
• LTR built-in
• Upgradeable to 6.25 digital
• Detachable front panel
• DB-25 connector
• Built-in ...specific application is claimed or asserted in this comparison. 42008
KV
Icom F5011 / F6011 Reviews
Do you have an experience with the Icom F5011 / F6011 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!