Icom F3210D / F4210D Support and Manuals
Get Help and Manuals for this Icom item
This item is in your list!
View All Support Options Below
Free Icom F3210D / F4210D manuals!
Problems with Icom F3210D / F4210D?
Ask a Question
Free Icom F3210D / F4210D manuals!
Problems with Icom F3210D / F4210D?
Ask a Question
Popular Icom F3210D / F4210D Manual Pages
Instruction Manual - Page 2
...i SAVE THIS INSTRUCTION MANUAL- Ask your dealer for the IC-F3210D VHF DIGITAL TRANSCEIVER and the IC-F4210D UHF DIGITAL TRANSCEIVER. This instruction
manual contains important operating instructions for details.
FOREWORD
READ ALL INSTRUCTIONS carefully and completely before
using the transceiver. Equipment damage may occur. See the operating guide for details of IDAS (ICOM Digital Advanced...
Instruction Manual - Page 3
... approved by Icom Inc., could void your authority to correct the interference at his own expense. CAUTION: Changes or modifications to this transceiver under FCC regulations. Operation of the FCC Rules.
FCC INFORMATION
• FOR CLASS A UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the instruction manual, may cause...
Instruction Manual - Page 13
2 PANEL DESCRIPTION
1
e LED INDICATOR (p. 7)
2
➥➥ Lights red* while transmitting.
3
* When the attached battery type is set to "Alkaline Dry," the LED
indicator lights orange.
4
➥➥ Lights green while receiving a signal, or when the squelch is open.
5
➥➥ Lights or ...
Instruction Manual - Page 14
R* • RX: Lights while receiving a signal. R*
R*
R*
R*
• Channel Error: A non-programmed channel is set to make a call. O
O
* When the attached battery type is selected.
O O O
O O O
• Audible: Blinks slowly when a mute is activated. R*
R*
• TX low Battery 2: Very Low Battery ...
Instruction Manual - Page 19
... repeat the procedure until one beep is heard.
10
qqRotate [VOL] to turn OFF the trans- [ROTARY SELECTOR] 11
ceiver's power.
[VOL] 12
wwSet [ROTARY SELECTOR] to any
channel other than Channel 16.
13
eeWhile holding down [PTT], the count down beeps sound. After that, the confirmation beeps...
Instruction Manual - Page 20
... one of memory channel keys, [MR-CH 1] to select channels, and they may differ, depending on your system set up. When turning ON the power, the transceiver automatically starts scanning. AUTOMATIC SCAN TYPE: Channel setting is detected.
13 Scanning stops when a signal is not necessary for this type. 3 BASIC OPERATION
■■...
Instruction Manual - Page 22
... transmitting. • Penalty timer Once the time-out timer activates, transmitting is received. - However, depending on the preprogrammed
settings, you can transmit when the call includes an unmatching (or matching) CTCSS (DTCS), RAN code*, or Individual or Talkgroup ID*. *Digital operation only - A signal with the un-matched (or matched) CTCSS (or DTCS...
Instruction Manual - Page 23
... operation may not be available, depending on the preset- 18
ting. Ask your headset performance).
16
wwSet [ROTARY SELECTOR] to Channel 16.
3
[ROTARY SELECTOR]
4
[VOL]
5
eeWhile holding down [... to 4 (maximum).
11
• A beep sounds after pushing
[Upper] or [Lower].
12
An error beep sounds if you try
to decrease less than 1 or try to
13
increase more than 4.
14
Therefore...
Instruction Manual - Page 24
...While holding down [Upper], ro- Ask your dealer for details.
17
wwSet [ROTARY SELECTOR] to increase more than Chan-
3 BASIC OPERATION
■■Setting the squelch level
The squelch circuit mutes the received audio signal, depending on the presetting. A n error beep sounds if you try
to decrease less than 0 or try to...
Instruction Manual - Page 25
... push-
1
16
ing [Lower].
17
ttRotate [VOL] to turn the trans- ceiver power OFF.
[ROTARY
wwSet [ROTARY SELECTOR] to exit the
4 (Linked)
18
beep level adjustment mode.
3 (Linked)
19
NOTE: This operation may...]
[VOL] 5 6
any channel other than Chan- 3 BASIC OPERATION
■■Setting the Beep level
1
The beep function can be turned ON or OFF, and its level can de-...
Instruction Manual - Page 26
... Ringer level
The Ringer level can determine the current
4
level setting by the type of beep
3
that sounds.
Ask your dealer for details.
4...turn ON the power
and enter the Ringer level ad- Therefore,
you can be available, depending on the presetting. wwSet [ROTARY SELECTOR] to 5 (Linked).
[Upper] operation
[Lower] operation
• A beep sounds after pushing
5
[...
Instruction Manual - Page 31
... an explosion. 3
R DANGER! Use the battery only with any part of 12
the body that is not specified in this instruction manual.
7
R DANGER! Using the battery out of these
conditions occur,.... NEVER put the battery in a microwave oven, high- 13
pressure container, or in your Icom dealer or distributor.
11
R WARNING! NEVER incinerate used battery packs, since internal 2 battery gas...
Instruction Manual - Page 37
Before you purchase a BC-197, check the type of battery you are two types of BC-197 chargers for the IC-F3210D series
or IC-F4210D series transceivers. One is for Ni-MH batteries, and 3
the other is
printed on the 9
inside bottom of the charger adapter, and the type of ...
Instruction Manual - Page 44
qqRotate [VOL] to any channel other than Channel 16.
wwSet [ROTARY SELECTOR] to turn ON the power to switch the VOX function ON or OFF. • One beep sounds when the VOX function is turned ...
Instruction Manual - Page 45
... headset.
12
• The adjustable range is 1 (minimum) to 10 (maximum).
13
• A beep sounds after pushing [Upper] or [Lower].
14
If the level is set on 1 or 10, an error beep sounds after pushing.
Therefore, you can be available, depending on the presetting. Ask your dealer for details.
19
•...
Icom F3210D / F4210D Reviews
Do you have an experience with the Icom F3210D / F4210D that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!