Icom F3031S / F4031S Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom F3031S / F4031S manuals!
Problems with Icom F3031S / F4031S?
Ask a Question
Free Icom F3031S / F4031S manuals!
Problems with Icom F3031S / F4031S?
Ask a Question
Popular Icom F3031S / F4031S Manual Pages
Instruction Manual - Page 2
... shock may occur. Ask your dealer.
RWARNING!
and the Icom logo are pre-programmed by your dealer for the IC-F3031S, IC-F3033S, IC-F3036S VHF TRANSCEIVERS and the IC-F4031S, IC-F4033S, IC-F4036S UHF TRANSCEIVERS. IMPORTANT
READ ALL INSTRUCTIONS carefully and com-
This instruction manual includes some functions which are usable only when they...
Instruction Manual - Page 3
...a ringing in areas with Icom radios or Icom chargers. DO NOT use .
tery pack and jack cover are securely attached to , or touching exposed parts of the transceiver are dry ...while transmitting. The transceiver warranty does
not cover any problems caused by unauthorized modification.
NEVER short the terminals of time.
Only Icom battery packs are tested and approved for long periods...
Instruction Manual - Page 4
...instruction manual, may cause harmful interference to part 15 of the FCC Rules.
For U.S.A. This equipment generates, uses and can radiate radio frequency energy and, if not installed... to operate this transceiver, not expressly approved by Icom Inc., could void your authority to turn the transceiver...replaced. The IC-F3031S, IC-F3033S, IC-F3036S,
IC-F4031S, IC-F4033S and IC-F4036S meet IP67...
Instruction Manual - Page 5
... 5
3 BASIC OPERATION 8-14 ■■Turning power ON 8 ■■Channel selection 9 ■■Call procedure 9 ■■Receiving and transmitting 10 ■■User set mode 12 ■■Emergency Call 12 ■■Priority A channel selection 13 ■■Man Down Emergency Call 13 ■■Stun function 13...
Instruction Manual - Page 9
...voice scrambler function is activated.
3
o
u BELL INDICATOR
4
!0
Appears or blinks when the specific 2-tone code is received, according to a specified level, low
13
power is selected automatically.
14
t AUDIBLE... ALPHANUMERIC DISPLAY
9
Displays an operating channel number, channel name,
10
Set mode contents, DTMF code, etc.
11
12
Appears when low output power is selected. •...
Instruction Manual - Page 10
...code channel after pushing [TX
Code CH Select]. ➥ Push to activate the function depends on the Power ON Scan set...A (Rewrite)] or [Prio B (Rewrite)] for details concerning your Icom dealer or system operator for 1
second to reassign the operating channel ...
■■Programmable function keys
The following explanations, the specific key is turned ON; Push to the intended use ...
Instruction Manual - Page 11
... signal level of the optional ports in the optional unit connector. The selected channel remains set as the continuous tone channel until another channel is added to the current scan list, ...the display shows "SCAN ON." SCRAMBLER FUNCTION Push to change the tone frequency/code setting. H old down this key for 1 second to display the current scan list, and then push [CH...
Instruction Manual - Page 12
... is necessary before transmitting the call. • The emergency call is assigned to exit user set mode is displayed on the LCD if programmed. • If you call silently or audibly
depending... surveillance function ON or OFF. User set mode. DTMF AUTODIAL KEY ➥ P ush to enter the ID code channel selection mode directly.
TX CODE CHANNEL SELECT KEY Push to enter the...
Instruction Manual - Page 14
... System Operator's instructions. • This may be necessary depending on programming. • Refer to voice transmission.
qqSelect the desired TX code channel or 2-tone code ac- Selective ...desired zone. AUTOMATIC SCAN TYPE: Channel setting is not necessary for selection. Scanning stops when receiving a call specific station(s) only and prevent unwanted stations from contacting you.
Instruction Manual - Page 15
...9632;■Receiving and transmitting
CAUTION: Transmitting without an antenna may not be necessary depending on the setting.
IMPORTANT: To maximize the readability of your signal; 1. See page 1 for a
The ... [VOL] to 4 inches) from the microphone is in sequence.
NOTE: When a matched RX code signal is received, audio from your sig-
• Penalty timer Once the time-out timer is...
Instruction Manual - Page 17
... call transmission, the transceiver stands by in the audible mode for a specified time period.*
• Auto RX function After the emergency call operation.
NOTE: User set mode is also available via a programma-
* Depending on the presetting, the following functions are Backlight, Beep, Beep
Level, SQL Level, Mic Gain, Battery Voltage, Signal...
Instruction Manual - Page 18
... the certain emergency call is automatically transmitted once, or repeatedly. Entering of the password (p. 8) or receiving a specified ID, set as a revive ID, is also available with the MDC 1200 signaling system. ...placed in a horizontal position for details.
■■Stun function
When the specified ID, set as a stun ID or kill ID, is received, the stun function is necessary to ...
Instruction Manual - Page 20
...Icom battery packs are tested and approved for use a wet battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to wipe it is not specified in this instruction manual...that is specified. Use the battery only with Icom radios or Icom charger. Use and charge only specified Icom battery packs with the transceiver for any other ...
Instruction Manual - Page 29
...Icom transceiver.
Icom is not responsible for the destruction or damage to an Icom transceiver in a hazardous environment, etc. OPTIONS 7
DDOPTIONAL UNITS
• UT-96R 5 tone unit • UT-108R dtmf decoder unit Provides pager and code...Provides measure of safety when working in the event the Icom transceiver is used with equipment that provides convenient
operation while hanging...
Instruction Manual - Page 30
... and what to transmit by the manufacturer for use with this radio by the manufacturer or antenna specifically authorized by pressing the "PTT" switch.
• ALWAYS keep the antenna at least 5... for exposure and can cause the radio to do so. 8 SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic en-
To provide the recipients of accessories other devices or systems...
Icom F3031S / F4031S Reviews
We have not received any reviews for Icom yet.