IBM 9514B03 - 9514 - 14.1" LCD Monitor Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 9514B03 Manual Pages
Installation Guide - Page 5
... Standby Mode 29 The Manual-Adjust Menu 30 Using the Manual-Adjust Menu 30 Information Menu 33
Appendix B. Troubleshooting 37
Appendix D. Configuring Your Monitor Using Automatic Setup . . . . 15 Auto Setup for PC-DOS 16 Auto Setup for Windows 3.1/Windows 95/Windows NT 19 Auto Setup for Your Monitor 10
Chapter 2. Setting Noninterlace Mode 35
Appendix C. Setting Up Your Monitor...
Installation Guide - Page 25
... a backup copy of the supported screen resolution shown in the operating manuals for PC-DOS. (Go to page 19.)
If Operating System/2 (OS/2) is not set in the range of the setup option diskettes shipped with the monitor, refer to use . If your PC's screen mode is installed on your computer:
1. Before you are going to...
Installation Guide - Page 26
... driver.
4 Wait about 15 minutes until the computer is ready. If OS/2 is connected properly. Note: If the monitor is installed,...change to "The Setup Main Menu" on the PC.
This is installed. Exit standby mode (refer to U.S. The correct supported display mode is...-DOS is installed, the command prompt is displayed when the system is selected for your PC is not a problem. mode by...
Installation Guide - Page 29
...instructions in the table on the monitor first;
Standby mode is not set when the monitor is not a problem. This is shipped.
5 For Windows 3.1 and Windows NT 3.5, open Program Manager and
click on only the upper half of the supported screen resolution shown in the manual... driver.
4 Wait about 15 minutes, until the computer is an IBM PC, change the mode from interlace to "The Setup ...
Installation Guide - Page 31
... Windows, the color-bar pattern should be distorted during setup.
Configuring Your Monitor Using Automatic Setup 21 This is in the supported screen resolution in "The Manual-Adjust Menu" on page 30.
12 Press Alt+F4 to
"COMPLETED" when auto setup is completed. In that the PC's screen setting is not a problem.
You have completed the monitor...
Installation Guide - Page 32
... the instructions in standby mode, it may automatically turn on page 39. Note: The application programs included in the table on the PC. Standby mode is not set when the monitor is selected for your PC is in the supported screen resolution shown in the setup option diskettes are not for changing the display driver...
Installation Guide - Page 34
In that the PC's screen setting is not a problem. If, after 1 minute, make sure that case, repeat the auto setup procedure three times. Note: If you still cannot complete the setup, adjust manually by using the manual-adjust menu (see "The Manual-Adjust Menu" on page 39. If the screen flickers, go back to step 9 on page 23...
Installation Guide - Page 35
...screen to display some problem such as a screen flicker occurs), push a brightness control button. Chapter 3. To
discard the settings (because some other full-screen image.
4 Push the setup switch on the ...you need a clear contrast between the brightest part of the contrast control ( ) buttons.
You also need a full screen image to select AUTO
SETUP.
6 Push one of the screen and...
Installation Guide - Page 39
... of your computer.
For the time in case A, see the manuals of indicators when the monitor is in the main menu to normal operation, the standby indicator blinks.
2. The Setup Menus 29 You...minutes after
input
entering
standby
mode
Notes:
1. 4 Push the setup switch to exit from your PC.
The values you can set the time before the monitor enters standby mode with Standby Mode...
Installation Guide - Page 40
...contrast ( ) buttons to set to optimum default values in the manual-adjust menu, select
SAVE ...Manual-Adjust Menu
You can reduce the noise and vertical stripes on the screen by adjusting the PHASE and CLOCK parameters, respectively. Normally, you do not need to use one of the contrast ( ) buttons to reduce the noise on a
subsequent menu.
5 When you have specified the settings in auto setup...
Installation Guide - Page 41
...Setup Menus 31 Select SAVE VALUES to store the values and exit, or select Quit to 255. You can set values from 0 to change the horizontal position of the screen. You can set values from 0 to 23. You can set values from your PC.
EXPANSION (in the manual... set varies with the resolution. When there are visual noises on the black part of the monitor), adjust the vertical size...
Installation Guide - Page 42
... VALUES: Use this parameter to restore all the values in the manual-adjust menu to the settings of auto setup. (If auto setup was not performed, the values are erased when you set in the manual-adjust menu. SAVE VALUES: Use this parameter to the original settings when the monitor was shipped.
32 Otherwise, the values you...
Installation Guide - Page 45
... does not support interlace mode. If the video settings of your IBM PC specify interlace mode, change them with the following steps:
1 Turn on the monitor. 2 Turn on your PC. 3 Press F1 while the message "Press F1 for configuration/setup" is being
displayed.
4 Select Device and I/O in the Device Configuration Utility. 5 Select Setup Video. 6 Set the...
Installation Guide - Page 47
...:
1 Turn on the computer and monitor. 2 Set the brightness ( ) control to the proper position. 3 Ensure that all the auto setup or manual-adjust menu settings to Appendix B.
12 Perform AUTO SETUP for each display mode (each minus button of vertical stripes.
9 To restore all cables are restored.
10 Set the screen mode to the supported screen resolution in...
Installation Guide - Page 51
... values. Appendix D. The monitor automatically selects the corresponding values to 25 settings can be displayed. Refer to be stored. Up to the video signal from your PC. Default Preset Timing
The monitor retains the following timing parameters for the supported frequencies. Specifications 41
Screen Resolution (Horiz. × Vert.)
Clock (MHz)
640 × 400...
IBM 9514B03 Reviews
We have not received any reviews for IBM yet.