IBM 6400-I10 Support and Manuals
Get Help and Manuals for this IBM item
This item is in your list!
View All Support Options Below
Free IBM 6400-I10 manuals!
Problems with IBM 6400-I10?
Ask a Question
Free IBM 6400-I10 manuals!
Problems with IBM 6400-I10?
Ask a Question
Popular IBM 6400-I10 Manual Pages
Operation Guide - Page 1
6400 Line Matrix Printers
Operator's Guide
Cabinet and Pedestal Models
Form Number S544-5641-00 ©Copyright IBM Corp., 1998
Operation Guide - Page 3
S544-5641-00
6400 Line Matrix Printers
Operator's Guide Cabinet and Pedestal Models
Operation Guide - Page 5
... - gives instructions for the IBM 6400 printer. describes the operator panel and how to load paper and ribbon, and how to change formatting features. Pedestal Model
Operator's Guide
i About this Operator's Guide
This guide describes basic operating procedures for clearing paper jams, cleaning the printer, and understanding fault messages. Troubleshooting -
Cabinet Model
This document...
Operation Guide - Page 6
... notice indicates the possibility of damage to proper operation of the notices in this operator's guide
Conventions
Notes and Notices In order to avoid injury to yourself or damage to the printer, follow the directions in the IBM 6400 Line Matrix Printer Safety Information booklet. Message Display
These boxes show display messages as they appear on the...
Operation Guide - Page 45
... paper jams, ribbon jams with potential for ribbon damage, smeared ink, or wavy print. Refer to match the paper thickness.
Lower Paper Guide
Pedestal Models
Operator's Guide
31 Set it to the...set the forms thickness lever too tightly; NOTE:
Thin Paper = single sheet Medium Paper = two-part form Thick Paper = six-part form
22 On pedestal models:
Guide the paper over the lower paper guide...
Operation Guide - Page 46
... tractors, over the lower paper guide, and into the paper stacking area. Cabinet Models
Lower Paper Guide
25 Feed enough paper to set the top-of-form. If ...Guide Ensure that the paper folds the same way in the output area (inside the cabinet).
27 Close both doors, if the length of this .
b. If there is data in the printer buffer, such as it does in the supply area.
26 On cabinet models...
Operation Guide - Page 61
...only when using the top exit paper path. 9 Close the printer cover.
10 Press Start to place the printer in
READY state.
11 On cabinet models:
When printing, open the rear cabinet door and ensure that... cabinet door.
12 On pedestal models:
When printing, ensure that the paper folds the same way in the stacking area as it does in the supply area. setting topĆofĆform
Operator's Guide
47
Operation Guide - Page 72
... UNLOCKED
3 Press Menu to unlock the
PROGRAM state. OPERATOR MENU CONFIGURATION MANAGEMENT
CONFIGURATION MANAGEMENT RECALL CUSTOM SET
RECALL CUSTOM SET FACTORY DEFAULT*
58
Operator's Guide
See page 56 to place the printer in the
NOT READY state.
OPERATOR MENU PRINTER CONTROL
4 Press Scroll ° until you previously stored, or the factory default configuration. The following...
Operation Guide - Page 89
Pedestal Models
Operator's Guide
75 attention
Always apply the cleaning solution to the cloth; never pour cleaning solution directly onto the printer. DANGER:
Switch off printer power and unplug the printer power cord before cleaning the printer. Clean the windows with a soft, lint-free cloth and mild detergent. Cleaning the Printer
Periodic cleaning ensures efficient operation ...
Operation Guide - Page 93
... print light print light print on the ribbon path diagram. Print quality can cause tearing of forms position
Corrective Action
1 Adjust the forms thickness lever setting. continued next page
Operator's Guide
79 Solving Printer Problems
If you are having print quality or other problems, locate your printer problem in the Setup Guide.)
1 Set the forms thickness lever for thicker paper...
Operation Guide - Page 99
... error. (Serial interface) Check printer serial port configuration setup. No action necessary. Enable poll timeout. Load paper.
Ensure that it matches host settings. Poll timeout error.
A timeout message is sent to the host if paper is set to Send to clear the paper out fault. Printer attach status message.
Contact an IBM service representative.
The printer...
Operation Guide - Page 103
... an IBM service representative.
Contact an IBM service representative. Contact an IBM service representative. Contact an IBM service representative. Stop printing and allow the printer to ground. Operator's Guide
89
Contact an IBM service representative. If fault reoccurs, contact an IBM service representative. Hammer driver circuits on the controller board.
Fatal firmware error...
Operation Guide - Page 104
... board. Contact an IBM service representative.
113 PROTECTED INSTRUCTION SEE USER'S GUIDE
Fatal firmware error on the controller board. Contact an IBM service representative.
117 A TO D OVERRUN SEE USER'S GUIDE
Fatal firmware error on the controller board. Contact an IBM service representative.
115 ILLEGAL INSTRUCTION ACCESS SEE USER'S GUIDE
Fatal firmware error on the controller...
Operation Guide - Page 106
...INVALID COMMAND SEE USER'S GUIDE
Fatal firmware error on the controller board. Contact an IBM service representative.
130 PAPER FEED PARTLY ENERGIZED SEE USER'S GUIDE
Fatal firmware error on the controller board. Contact an IBM service representative.
132 RIBBON INVALID COMMAND SEE USER'S GUIDE
Fatal firmware error on the controller board. Contact an IBM service representative.
135 PLATEN...
Operation Guide - Page 108
... action necessary.
No action necessary. Contact an IBM service representative.
94
Operator's Guide Bad coils are indicated.
Status message. OPERATOR MENU UNLOCKED PA1 SELECTED PA2 SELECTED P05 DIAGNOSTIC TEST PASSED P17 SECURITY VIOLATION
Status message. Status message. Status message. No action necessary. Printer state message: printer is offline, not in communication with host...
IBM 6400-I10 Reviews
Do you have an experience with the IBM 6400-I10 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for IBM yet.
Earn 750 points for your review!