Husqvarna MZ61ROPS Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna MZ61ROPS manuals!
Problems with Husqvarna MZ61ROPS?
Ask a Question
Free Husqvarna MZ61ROPS manuals!
Problems with Husqvarna MZ61ROPS?
Ask a Question
Popular Husqvarna MZ61ROPS Manual Pages
Owner Manual - Page 2
... manual....repairs.
Note that the machine will fulfill the requirements. CONFORMITY CERTIFICATES
USA requirements
Labels are valuable documents. WARNING! Do not modify or install...instructions, and must not be replaced. Engine exhaust and certain vehicle components contain or emit chemicals considered to the operator or other parts voids the warranty. Do not remove these instructions...
Owner Manual - Page 4
... operator manual provides a Service Journal. Towing
If machine is correctly attached. Do not tow on Public Roads
Check applicable road traffic regulations before using or servicing the machine. Operating
This machine is taken to avoid jack-knifing. The machine must only be operated, maintained, and repaired by persons familiar with delivery. Use only approved repair parts...
Owner Manual - Page 5
... parts. See the certificate in the Service Journal in service questions, warranty issues, etc., consult the following professional:
This manual belongs to the engine compartment. The plate states:
• The engine's model.
• The engine's type.
• Code
Please have a barcode decal affixed at the rear.
5 This ensures that you need spare parts or support in this operator manual...
Owner Manual - Page 7
... the mowing area and in the manual before operating. WARNING! IMPORTANT INFORMATION The American Academy of Pediatrics recommends that you last saw them carefully. General Operation
• Read, understand, and obey all the safety instruction that can fall off . WARNING! Children who operate, maintain, and/or service this machine must first read and...
Owner Manual - Page 9
...service as necessary.
• Do not interfere with the starter circuit if there is in handling gasoline. WARNING! Use protective glasses for maintenance work.
• Maintain or replace safety and instruction... adjustments or repairs with the engine running the engine at all times until problem has been ...engine must not be started when the driver's floor plate or protective plates for...
Owner Manual - Page 12
Motion control levers 2. Park brake 3. Service meter
11. Deck lift 15. The rider is regulated and ...1
6. Fuses 8. Throttle 12. Fuel tank 5. Ignition switch 10. Seat adjustment 14. Deck release pedal CONTROLS
This operator manual describes the Husqvarna Zero Turn Rider.
Transmission from the engine is made via belt-driven hydraulic pumps. Tracking knob 4. Hydro release...
Owner Manual - Page 15
... Operation section. The 7.5 A is 15 psi (1 bar).
1. Tracking
The desired cutting height is set with nut.
5. Recommended air pressure for the rear tires is for the mower deck coupling. The... handled.
15 The 20 A is not tracking straight, check the air pressure in automobiles. See Manual Transport in the fullforward position.
2. Fuses are flat pin fuses type as an empty parking lot...
Owner Manual - Page 21
...)/ Replace mower blades
♦
♦♦♦
♦
●●
● = Described in this manual ♦ = Not described in this manual ■ = Refer to OFF position and
remove the key. • Make sure the blades and all moving parts
have completely stopped.
21 WARNING! For those points not described in this manual, visit an authorized service...
Owner Manual - Page 22
... negative grounded system.
Positive terminal must also be connected first to the engine manufacturer's manual
1) First change after 8-10 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.
2) In dusty conditions, cleaning and replacement are necessary more frequently.
3) Performed by allowing a wrench or other objects to contact...
Owner Manual - Page 23
...a maintenance free battery and does not need servicing. STD BATTERY
STATE OF
CHARGE
APPROXIMATE CHARGING TIME...20 Amps 10 Amps
12.6V
100%
- Replacing
1. Slide mount bracket back up over battery ... end of the battery with a
wire brush until supported by the seat rod.
2. To remove cables, ...
• See chart for the terminal screws. Install the new battery with the discharged battery, away ...
Owner Manual - Page 25
...manual).
2. Remove both fan covers.
3.
Engage the park brake. Blades are not adjustable. Remove clutch stop . 7. Let the service workshop decide whether a blade with large nicks can be repaired/ground or must be replaced...122 Nm). Install and tighten the clutch stop to access fan covers. Install the deck belt.
Check the blade mounts.
Install new or re...instructions again.
2.
Owner Manual - Page 27
... daily. Examine the machine for service. NOTE: Tire must be adjusted to prevent scalping in most terrain conditions. The rollers must turn freely.
Install in the correct position to support the deck.
27 Do not ... 200 hours. If wheels do not turn freely take care with normal water pressure. To replace, remove the nut and caster bolt. Clean the machine directly after it is at the ...
Owner Manual - Page 29
... on each set of the fill tube threads. Engage park brake.
2. Let the used oil fully drain from the area around the oil fill cap.
3. Replace and tighten the drain hose plug.
7. Replace and tighten the oil fill cap when the oil level is near to the Service Journal for the correct replacement oil and...
Owner Manual - Page 32
...is very flammable and can cause serious personal injury and property damage. Service When ordering spare parts, please specify the purchase year, model, type, and serial number. Use a degreaser and warm water. ... after adding the stabilizer so that it reaches the carburetor. Touch up at an authorized service workshop is evenly distributed and then refit the spark plug.
6. Store the machine in...
Owner Manual - Page 34
Refer to the engine manufacturer engine specifications.
74"
188 cm
73"
183... Number of Blades Blade Length Anti-scalp roller Nose roller Sprung Seat Hinged Arm Rests Service Meter Blade Engagement Deck Construction Productivity
DIMENSIONS Weight Base Machine Length Base Machine Height Base Machine... production engine for the engine model measured using SAE Standards for engine gross power.
Husqvarna MZ61ROPS Reviews
We have not received any reviews for Husqvarna yet.