Husqvarna 525iLK Motor unit Support and Manuals
Get Help and Manuals for this Husqvarna item
This item is in your list!
View All Support Options Below
Free Husqvarna 525iLK Motor unit manuals!
Problems with Husqvarna 525iLK Motor unit?
Ask a Question
Free Husqvarna 525iLK Motor unit manuals!
Problems with Husqvarna 525iLK Motor unit?
Ask a Question
Popular Husqvarna 525iLK Motor unit Manual Pages
Owner Manual - Page 2
.... Contents
Introduction 2 Safety 4 Assembly 11 Operation 13 Maintenance 16
Troubleshooting 18 Transportation, storage and disposal 18 Technical data 19 Accessories 20 Registered trademarks 21
Introduction
Intended use
This power unit is a bare unit that only function together with the approved accessory manual. Battery 15. Battery charger cord 11. Product overview
22...
Owner Manual - Page 3
...repaired.
1938 - 003 - 24.02.2023
3 or min-1
nute. Note: Other symbols/decals on the product name label. Cutting attachment guard
Symbols on you understand the instructions... boots. 23.
Keep all parts of the product.
Use approved protective gloves. Manufacturer
Husqvarna AB Drottninggatan 2, SE-561 ...manual. Keep a minimum distance of 15 m to
certification requirements ...
Owner Manual - Page 4
... parts. A moment of inattention while operating power tools may result in the presence of
injury or death for the operator or bystanders if the instructions in electric shock, fire and/or serious injury. Failure to the product, other materials or the adjacent area if the instructions in any adapter plugs with this power units manual...
Owner Manual - Page 7
... accessories or replacement parts.
•...from its original specification
• Never ...manual.
• Faulty cutting attachment can face. Since the machine is not recommended to make sure that the cutting attachment stops completely. Carry out the safety checks, maintenance and service instructions described in serious personal injury or the death of serious personal injury. Replace...
Owner Manual - Page 8
...: This device complies with Part 15 of the following two... Development Canada technical specifications.
Le pré...Husqvarna Professional Product, Inc.
9335 Harris Corners Parkway
Charlotte, NC 28269
United States
Telephone: +1 704 597 5000
E-mail: http://www.husqvarna.com/us/support/e-mail/
Personal protective equipment
WARNING: Read the warning
instructions... installed and used in ...
Owner Manual - Page 9
... The product's safety equipment must contact your service agent. If your machine fails any of these parts are not carried out professionally. a) The...both move back to Troubleshooting on or flashes, refer to their original positions. See instructions under the heading Introduction...maintenance is not carried out correctly and if service and/or repairs are located on twigs and branches. In...
Owner Manual - Page 10
...attached this power unit
manual together with approved accessory manual.
• Remove... the battery from the product. Hold the power trigger lockout against the handle (B) and make the cord more before you touch the cutting attachment.
1. Safety instructions...Manual.
• Make sure that the cutter on page 20. To increase the life of the operator.
Replace...
Owner Manual - Page 11
... nut, the knob and the screw, do the maintenance and servicing shown in this operator's manual. Tighten the bolt.
1938 - 003 - 24.02.2023
11 Strong detergent can easily cause injuries. The blades are professional repairs and servicing available for your servicing dealer for maintenance and servicing of the loop handle. 3.
Align the tab (A) with water...
Owner Manual - Page 12
...Adjust the length of the harness until it clicks into the coupling until the harness
support hook is recommended for the cutting attachment.
WARNING: Always use . Tighten the knob...Technical data on page 19.
12
1938 - 003 - 24.02.2023
C
To install the harness support hook
1. Install the harness support hook between the loop handle and the throttle handle. Hold tight in level with your...
Owner Manual - Page 13
... you use the product. Make sure that the raised section on the drive disc/support flange engages correctly in the gear housing. 3.
To attach the cutting attachment guard
...: Only use a cutting
attachment without an approved guard. Install the cutting attachment guard on the output shaft. 2. WARNING: Never use Husqvarna
original batteries with the bolt (C).
To remove the cutting ...
Owner Manual - Page 14
...inspections, maintenance and
servicing that are correctly ... speed. Replace the trimmer...parts away from the cutting attachment. Work position
• Hold the product with the mode button
The product has a mode button.
Withe the mode button the operator can cause damage to choose the next speed level. Push the mode button to set...manual. • Make sure that the function is not installed...
Owner Manual - Page 16
... the battery before
you must do a check of the other parts of the product with Husqvarna Fleet Services™. Do not use water. Put the product in Bluetooth® wireless ... product
1.
To connect to pair the product with a dry cloth. Follow the instructions about Husqvarna Fleet Services™, refer to the product.
4.
Examine that gives the commercial fleet manager an overview...
Owner Manual - Page 17
...the battery release buttons on page 17. Make sure that the terminals on models with two-piece shafts will seize if they are not lubricated regularly.
1938 ... use Husqvarna bevel gear grease. Remove the grease plug.
4. Replace the cutting attachment if it is charged. Make sure that the battery is damaged. Keep the battery guide tracks clean... the bevel gear.
6. Install the grease plug.
Owner Manual - Page 18
... and away from open contacts when you send the product. The product does not start Error LED is between 5 °C/41 °F and 45°C/113°F and away ... Remove the battery. Troubleshooting
User interface
LED display
Possible faults
Battery LED indicator flashes or- ange
Red error LED flashes
Overload. Dirt in a package. The product needs servicing.
Clean the cutting ...
Owner Manual - Page 19
..., domestic waste service or your dealer for more information about how to recycle your product.
Technical data
Technical data
525iLK together withTAB850
Motor
Motor type
Husqvarna E-torq BLDC
...levels 3
Vibration levels at a recycling station for electrical and electronic equipment. na.com/uk/services-solutions/vibration-calculator/.
1938 - 003 - 24.02.2023
19 Recycle it in storage for...
Husqvarna 525iLK Motor unit Reviews
Do you have an experience with the Husqvarna 525iLK Motor unit that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Husqvarna yet.
Earn 750 points for your review!