Husqvarna 525PT5S Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna 525PT5S manuals!
Problems with Husqvarna 525PT5S?
Ask a Question
Free Husqvarna 525PT5S manuals!
Problems with Husqvarna 525PT5S?
Ask a Question
Popular Husqvarna 525PT5S Manual Pages
Operation Manual - Page 2
...English It is extremely important that you read the operator's manual carefully and make sure the power is in the Technical data...insulated. CAUTION! This machine is specified in accordance with chain oil and adjusting oil flow
2 - If have to...markets. Regular cleaning is switched off before you understand the instructions before using the machine. Always keep a distance of at...
Operation Manual - Page 3
... Fitting the bar and chain 15 Fitting ...the impact guard 15 Telescopic function 16 Adjusting the harness 16 FUEL HANDLING Fuel safety 17 Fuel 17 Fueling 18 STARTING AND STOPPING Check before starting 19 Filling with oil 19 Starting and stopping 19 WORKING TECHNIQUES General working instructions... pole saw is extremely important that you read the operator's manual ...
Operation Manual - Page 4
.... If the retailer who sells your nearest service workshop. Husqvarna is working today. In 1956, the first motor driven lawn mowers appeared, followed by chain saws in the world of forest and garden products, with repairs and service whenever this machine, make sure that the operator′s manual is our wish that you will be satis...
Operation Manual - Page 5
...27
28
29
What is what?
1 Saw chain 2 Guide bar 3 Bar nut 4 Locking knob 5 Chain lubrication adjustment screw 6 Filling with chain oil 7 Chain oil tank 8 Chain tensioning screw 9 Shaft 10 Front handle 11 Harness support hook 12 Stop switch 13 Throttle trigger lockout... manual 25 Harness 26 Transport guard, bar 27 Combination spanner Chain tensioner 28 Combination spanner 29 Allen key
English - 5
Operation Manual - Page 6
...service instructions described in a
!
This machine produces an
! Running an engine in this machine.
Never allow children to consult their physician and
the medical implant manufacturer before
operating this manual. loaded stop switch and can cause serious, even fatal injuries.
A pole saw... or a visor must be carried out by
low speed and force on the starter
handle, even...
Operation Manual - Page 11
...• Always file cutting teeth from your chain and adjusting raker clearance
- sharpening instructions considerably
increases the risk of kickback is called the cutting link and this consists of the bar first. increased with a badly sharpened chain! Cutting angle - WARNING! GENERAL SAFETY PRECAUTIONS
Sharpening your chain. Round file diameter
WARNING! General...
Operation Manual - Page 12
...; Place the file over the gauge.
• On a low-kickback cutting link the front edge of kickback is rounded. To maintain ...Setting the raker clearance
• Before setting the raker clearance the cutting teeth should be replaced.
General advice on the raker lip.
• The more frequently.
• Tension the chain as tightly as you draw the file over the part...
Operation Manual - Page 14
... there are not obstructed. Guide bar
Checking wear on cutting equipment Saw chain
Check the chain daily for: • Visible cracks in rivets and links. • Whether the chain is due to running with a slack chain. When the length of the cutting teeth has worn down to only 4 mm the chain must be replaced.
GENERAL SAFETY PRECAUTIONS
What to...
Operation Manual - Page 15
... groove in . Fit the guard with the hole in use for around 20 hours, re-tighten the screws to 4 Nm. A
Tension the chain by hand. English - 15
Tighten the bar nut finger-tight.
After the machine has been in the shaft as shown. A
B
• Tighten screw A. • Tighten screw B. A correctly tensioned...
Operation Manual - Page 17
...RON). highly inflammable and can occur.
Use low-emission petrol, also known as outboard oil (rated TCW...HUSQVARNA two-stroke engine oil, which is not under close supervision and when performing all service measures.
• Allow the machine to dispose of leakage, contact your service...The lowest octane recommended is no risk of any part of the engine, the spark plug cap must ...
Operation Manual - Page 19
...64257;tted before the
machine is started
! with any objects that lacks a part or has been modified outside its specifications.
The safety ... surface. Choke: Set the choke control in good working area.
English - 19 Check that all nuts and screws are tight.
• Make sure the chain is adequately lubricated.... with Husqvarna saw chain oil. • Refit the cap.
Operation Manual - Page 21
...setting.
• Make sure that falling branches can cause
! tool without first ensuring that they have a safe and stable working with a pole saw. Do not touch the
! Personal protection
• Always ensure you have read and understood the contents of the operator's manual...direction of your service workshop. Safety instructions while working instructions
IMPORTANT! Cutting ...
Operation Manual - Page 25
...the saw head.
If the machine is 0.65 mm. Blow clean with a suppressor. Gear
CAUTION! Always use Husqvarna's original... often in operating problems and starting difficulties. English - 25 All service on the cylinder....part number: 579 06 49-01
The air filter must be replaced after about a month in order to avoid: • Carburettor malfunctions. • Starting problems...
Operation Manual - Page 26
... safety point of the spark plug. Replace if necessary.
Clean the outside of the bar.
Check the fuel filter for ...saw chain is fitted with a suppressor.
X
Check that nuts and screws are tight. Check that there are not damaged. Check that must be carried out by an autorized service workshop. Clean the outside of view. Replace if necessary. Replace...
Operation Manual - Page 28
.... of February 26, 2014 "relating to Europe only)
We, Husqvarna AB, SE561 82 Huskvarna, Sweden, tel: +4636146500, declare that the pole saws Husqvarna 525PT5S with serial numbers dating from 2016 onwards (the year is clearly stated on behalf of the COUNCIL'S DIRECTIVE:
- English TECHNICAL DATA
Guide bar and saw chain combinations
The following standards have been applied:
EN ISO...
Husqvarna 525PT5S Reviews
We have not received any reviews for Husqvarna yet.