Product Manual
Page 2
...is not recommended. • Do not use as shown. Be sure to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for warranty service of the handle as described in the instructions. They ...Descriptions 4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4 Important Safeguards 2 Maintenance Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand...
...is not recommended. • Do not use as shown. Be sure to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for warranty service of the handle as described in the instructions. They ...Descriptions 4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4 Important Safeguards 2 Maintenance Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand...
Product Manual
Page 10
... bottom plate as shown with your cleaner. When purchasing a new belt, ask for HOOVER part No. 48414069. 3-23 10 Brush roll can start suddenly. Unplug cleaner when it is described below; the other end of belt over . Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll. To check condition of...
... bottom plate as shown with your cleaner. When purchasing a new belt, ask for HOOVER part No. 48414069. 3-23 10 Brush roll can start suddenly. Unplug cleaner when it is described below; the other end of belt over . Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll. To check condition of...
Product Manual
Page 11
... pulley as described in Fig. 4-1. To install new belt (with Hoover belt part no. 38528034 (belt package part no. 40201200). Push other side of belt toward groove (E) next to replace it into position by first sliding end, opposite the belt, into place. E C Inspecting V-belt The V-belt is designed to last for HOOVER part No. 48414088. 3-28 A Installing brush roll...
... pulley as described in Fig. 4-1. To install new belt (with Hoover belt part no. 38528034 (belt package part no. 40201200). Push other side of belt toward groove (E) next to replace it into position by first sliding end, opposite the belt, into place. E C Inspecting V-belt The V-belt is designed to last for HOOVER part No. 48414088. 3-28 A Installing brush roll...
Product Manual
Page 12
Insert brush roll through the top of turbine retainers (G) pointing down, slide retainers into grooves (H) in guard. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Remove bottom plate, belt guard and brush roll as described in Figs. 3-30 through 3-30. 3-35 F E 2. Turn agitator, ... insert the four tabs on edge of bottom plate into slots on brush roll. 6. Replace brush roll, belt guard, and bottom plate as described in good condition. If belt is cracked, gouged or broken, replace it is not normally replaced. Replace and tighten screws. 3-33 ...
Insert brush roll through the top of turbine retainers (G) pointing down, slide retainers into grooves (H) in guard. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Remove bottom plate, belt guard and brush roll as described in Figs. 3-30 through 3-30. 3-35 F E 2. Turn agitator, ... insert the four tabs on edge of bottom plate into slots on brush roll. 6. Replace brush roll, belt guard, and bottom plate as described in good condition. If belt is cracked, gouged or broken, replace it is not normally replaced. Replace and tighten screws. 3-33 ...
Product Manual
Page 13
Remove bottom plate as described in "The belt" section (Fig.3-18). 3-37 Installing groomers Lift off both...has been designed into position as follows: 1. When cleaner is for comparing the relative progressive performance of Hoover uprights only and not for comparison with any other brands. Do not send your cleaner to activate after ...will only result in North Canton for HOOVER part No. 39511004. The agitator is equipped with two ball bearings that should be lubricated periodically by : • checking the Yellow Pages under "Vacuum Cleaners - Check dirt cup pre-filter...
Remove bottom plate as described in "The belt" section (Fig.3-18). 3-37 Installing groomers Lift off both...has been designed into position as follows: 1. When cleaner is for comparing the relative progressive performance of Hoover uprights only and not for comparison with any other brands. Do not send your cleaner to activate after ...will only result in North Canton for HOOVER part No. 39511004. The agitator is equipped with two ball bearings that should be lubricated periodically by : • checking the Yellow Pages under "Vacuum Cleaners - Check dirt cup pre-filter...
Product Manual
Page 14
...pick up may settle to a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). Problem: Cleaner won 't pick up Possible cause Possible solution • Broken or worn belt • Replace belt. • Agitator brush roll worn...upright position. • Blockage in OFF position • Slide button to ON position (carpet) • Flat belt broken or worn • Replace belt. If a blockage occurs during floor cleaning: Turn cleaner OFF and disconnect from electrical outlet. 1. Check fullness of performance, check the items under "Cleaner won 't self-propel...
...pick up may settle to a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). Problem: Cleaner won 't pick up Possible cause Possible solution • Broken or worn belt • Replace belt. • Agitator brush roll worn...upright position. • Blockage in OFF position • Slide button to ON position (carpet) • Flat belt broken or worn • Replace belt. If a blockage occurs during floor cleaning: Turn cleaner OFF and disconnect from electrical outlet. 1. Check fullness of performance, check the items under "Cleaner won 't self-propel...