Hitachi P7K500 - Deskstar - Hard Drive Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi P7K500 manuals!
Problems with Hitachi P7K500?
Ask a Question
Free Hitachi P7K500 manuals!
Problems with Hitachi P7K500?
Ask a Question
Popular Hitachi P7K500 Manual Pages
Specifications - Page 13
... Monitoring and Analysis Reporting Technology)
• Support security feature
• Quiet Seek mode (AAM)
• 48 bit addressing feature
• ATA-8 compliant
• UDMA133 support
• Streaming feature set support
• World Wide Name
• Write Uncorrectable
• SATA 2.6 compliant
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 3
Specifications - Page 19
.... HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 11 4.5.2 Mechanical positioning
4.5.2.1 Average seek time (without command overhead, including settling)
Read Write
Command Type
1D/2D
Typical (ms) Max (ms)
14.0
14.7
15.0
15.7
Table 5 Mechanical positioning performance
The terms "Typical" and "Max" are used to correct arrival problems. The average seek time...
Specifications - Page 66
... CCTL(Command Completion Time Limit). Refer to section 5.1, "Reset Response" for the spindle to Sector Count Register when the device is not the same as the return value. COMRESET
COMRESET response is in Idle mode. 6.0 General
6.1 Introduction
This specification describes the host interface of Power On Reset. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 58...
Specifications - Page 71
... determine the error type.
Service. DRQ
CORR (COR) IDX
ERR
Data Request. The host should not attempt to 1 even if the host is received from the host. Index. IDX=1 once per revolution. Since IDX=1 only for timing purposes. Therefore, the host should not write the Command register when DRQ=1. Error. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev...
Specifications - Page 77
Disabling SMART shall disable the delivering of self-test. If the device receives a firmware modification, all error log data is discarded and the device error count for the marginal sectors to prevent the user data lost. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 69 The device performs the entire read scanning feature with reallocation for the life...
Specifications - Page 78
...
Following security levels are supported for this feature. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 70 The following commands are provided. Device Locked mode
The device disables media access commands after power on . 8.6 Security Mode Feature Set
Security Mode Feature Set is removed from the computer. With a device lock password, a user can be unlocked...
Specifications - Page 79
... operation
Normal operation
POR
Power off Device locked mode
Power off
POR
Device unlocked mode
Figure 28 Initial Setting
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 71 When the User Password is set, the device enables the Device Lock Function, and then the device is powered on reset or hard reset. The Master Password Revision Code is set to enable the...
Specifications - Page 85
... Max Unlock. When the password is set Max Unlock) until the next power cycle. This password is in the Set_Max_Frozen mode. The Set Max Freeze Lock command allows the host to the Set_Max_Unlocked mode. When this option, unexpected power removal or reset will not make the protected area remained accessible. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 77
Specifications - Page 100
...between
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (...set support
15-12 Vendor Specific
11-6
Reserved
5
Action Code 5 (SCT Data Table) supported
4
Action Code 4 (Features Control) supported
3
Action Code 3 (Error Recovery Control) supported
2
Action Code 2 (LBA Segment Access) supported
1
Action Code 1 (Long Sector Access) supported
0
SCT Feature Set supported...
Specifications - Page 131
... or any of supporting.
If a Device Configuration Set command has been issued reducing the capabilities, the response to cylinder low register.
10.4.2 Device Configuration Freeze Lock (Subcommand C1h)
The Device Configuration Freeze Lock command prevents accidental modification of error information is enabled
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev...
Specifications - Page 132
...data
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 124 Bits 7:0 of this word contain the value A5h. Bits 15:8 of this word contain the data structure checksum. Word
Content
0
0002h
Data Structure revision
1
Multiword DMA modes supported
15-3 Reserved
2 1 = Multiword DMA mode 2 and below are supported
1 1 = Multiword DMA mode 1 and below are supported...
Specifications - Page 147
...
10 Host Protected Area feature set
9 DEVICE RESET command
8 SERVICE interrupt
7 RELEASE interrupt
6 LOOK AHEAD
5 WRITE CACHE
4 PACKET Command feature set
3 Power management feature set
2 Removable media feature set
1 Security feature set
0 SMART feature set
Identify device information --Continued--
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 139
Specifications - Page 151
... those parameters are vendor specific.
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 143 Bit assignments
15-9 Reserved
8 Security Level
1= Maximum, 0= High
7-6 Reserved
5 Enhanced erase
1= Support
4 Expired
1= Expired
3 Freeze
1= Frozen
2 Lock
1= Locked
1 Enabled/Disable
1= Enable
0 Capability
1= Support
xxxxH * Current Set Feature Option. Note...
Specifications - Page 210
...Power Saving mode is Normal Idle mode (the same as follows:
When Low power idle mode is set to 10h or 90h, the value set to the Sector Count register specifies the specific ...DMA Setup FIS
02h
DMA Setup FIS Auto-Activate optimization
03h
Device-initiated interface power state transitions
04h
Guaranteed In-Order Data Delivery
06h
Software Settings Preservation
10.38.4 Advanced Power ...
Specifications - Page 214
...set. (L=1) In CHS mode, this register contains cylinder number which is to be set.(L=0)
H
In LBA mode, this register contains max head number.(L=0)
HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 206
When B=0, MAX Address which is set... non-volatile Set Max Address command until next power on or hardware reset. When
B=1, MAX Address which is set by
POR....
Hitachi P7K500 Reviews
We have not received any reviews for Hitachi yet.