Instruction Manual
Page 6
...NAILER CORRECTLY. HANDLE NAILER CAREFULLY. Because of high air pressure in the Nailer, cracks in use of wire collating fasteners can be left unattended since people who are not further used before repair. Handle the Nailer carefully. 32. Keep the Nailer...the Nailer or strike the Nailer against hard surfaces; USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY HITACHI. ...NAILER. Continued 27. Never allow the Nailer to operators and personnel performing maintenance. 2. IMPORTANT SAFETY INSTRUCTIONS FOR USING NV 65AH COIL NAILER WARNING 1. Ensure that Nailers...
...NAILER CORRECTLY. HANDLE NAILER CAREFULLY. Because of high air pressure in the Nailer, cracks in use of wire collating fasteners can be left unattended since people who are not further used before repair. Handle the Nailer carefully. 32. Keep the Nailer...the Nailer or strike the Nailer against hard surfaces; USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY HITACHI. ...NAILER. Continued 27. Never allow the Nailer to operators and personnel performing maintenance. 2. IMPORTANT SAFETY INSTRUCTIONS FOR USING NV 65AH COIL NAILER WARNING 1. Ensure that Nailers...
Instruction Manual
Page 8
...cap "No-mar push lever attachment" (It is attached in the Table below can be driven with this Nailer. NOTE: Use only genuine Hitachi nails to malfunction and resulting injuries. English SPECIFICATIONS Operating pressure Dimensions Length × Height × Width ...7 kgf/cm2) 3/8 NPT Thread NAIL SELECTION Only nails shown in the 1 magazine assembly) - 8 - Wire-collated coil nails Min. .209" (5.3 mm) Max. .252" (6.4 mm) 1-1/2" (38 mm) 2-1/2" (64 mm) Sheet-collated coil nails .090" (2.3 mm) .099" (2.5 mm) ACCESSORIES WARNING ⅷ Accessories other than those shown below...
...cap "No-mar push lever attachment" (It is attached in the Table below can be driven with this Nailer. NOTE: Use only genuine Hitachi nails to malfunction and resulting injuries. English SPECIFICATIONS Operating pressure Dimensions Length × Height × Width ...7 kgf/cm2) 3/8 NPT Thread NAIL SELECTION Only nails shown in the 1 magazine assembly) - 8 - Wire-collated coil nails Min. .209" (5.3 mm) Max. .252" (6.4 mm) 1-1/2" (38 mm) 2-1/2" (64 mm) Sheet-collated coil nails .090" (2.3 mm) .099" (2.5 mm) ACCESSORIES WARNING ⅷ Accessories other than those shown below...
Instruction Manual
Page 12
... Opening Pawl Feeder 2 Guide Surface NOTE: Be careful not to deform the collated wires and not to avoid accidental firing. ⅷ Choice of triggering method is ...damaged. (3) Place the nail coil in the magazine. Insert the first nail into the driving hole and the ⅷ Do not drive nails on top of the Nailer. 1) do not push Nailer on workpiece with the guide...close correctly. 4 Pulling the nails to reach the driving hole. Nailer at yourself or others in work area MUST wear safety glasses with side shields which conforms to bouncing of other nails or with finger. Press...
... Opening Pawl Feeder 2 Guide Surface NOTE: Be careful not to deform the collated wires and not to avoid accidental firing. ⅷ Choice of triggering method is ...damaged. (3) Place the nail coil in the magazine. Insert the first nail into the driving hole and the ⅷ Do not drive nails on top of the Nailer. 1) do not push Nailer on workpiece with the guide...close correctly. 4 Pulling the nails to reach the driving hole. Nailer at yourself or others in work area MUST wear safety glasses with side shields which conforms to bouncing of other nails or with finger. Press...