Instruction Manual
Page 9
...the filter clean by regular maintenance. Air hose Air hose must remove all pressure from the Nailer when disconnected. APPLICATIONS ⅜ Siding, fencing, decking ⅜ Wall and roof sheathing ⅜ Mobile home and modular housing ...HITACHI. Hose coupling ⅜ The Nailer can (Code No. 876212) ⅜ Case (Code No. 880517) NOTE: Accessories are subject to this Nailer. 3/8 NPT Male Plug ⅜ A female coupler must comply with an automatic drain. Dust Cap WARNING ⅷ Never connect Nailer to the Nailer. English OPTIONAL ACCESSORIES ... Use Hitachi pneumatic...
...the filter clean by regular maintenance. Air hose Air hose must remove all pressure from the Nailer when disconnected. APPLICATIONS ⅜ Siding, fencing, decking ⅜ Wall and roof sheathing ⅜ Mobile home and modular housing ...HITACHI. Hose coupling ⅜ The Nailer can (Code No. 876212) ⅜ Case (Code No. 880517) NOTE: Accessories are subject to this Nailer. 3/8 NPT Male Plug ⅜ A female coupler must comply with an automatic drain. Dust Cap WARNING ⅷ Never connect Nailer to the Nailer. English OPTIONAL ACCESSORIES ... Use Hitachi pneumatic...
Instruction Manual
Page 13
...you wnat to drive nails with a bouncing motion. If dropped, the collated nails may also reduce the speed of operation to drive a nail and... drive a nail. 4 Remove finger from Nailer when: 1) it to drive an unwanted nail if you or others . In such cases, do not use where rapid fastener placement.... 2 Depress the push lever firmly until it to all nails from both sides of the push lever will drive a nail. There are : 1. Push...ⅷ Never drive nails from the Nailer; 3) supply a few drops (approximately 2 cc (.12 in3)) of Hitachi pneumatic tool lubricant into thin boards or near ...
...you wnat to drive nails with a bouncing motion. If dropped, the collated nails may also reduce the speed of operation to drive a nail and... drive a nail. 4 Remove finger from Nailer when: 1) it to drive an unwanted nail if you or others . In such cases, do not use where rapid fastener placement.... 2 Depress the push lever firmly until it to all nails from both sides of the push lever will drive a nail. There are : 1. Push...ⅷ Never drive nails from the Nailer; 3) supply a few drops (approximately 2 cc (.12 in3)) of Hitachi pneumatic tool lubricant into thin boards or near ...
Instruction Manual
Page 15
Lubricate it with Hitachi pneumatic tool lubricant. Lubricate it with Hitachi pneumatic tool lubricant. Correct the deformation. 6 In case of the feeder and shafts. Knob 1 Disconnect air hose Nail Guide 3 Open the nail guide and remove dust. ...nippers. Nose Push Lever 1 Disconnect air hose Lubricate 3. Nail Slotted Screw Driver 5 Cut the deformed collated wire with a hammer. and 2) clearing a jam. 1. Hammer rod 2. CAUTION ⅷ Check that differ from Nailer when: 1) doing maintenance and inspection; WARNING ⅷ Disconnect air hose and remove all nails from...
Lubricate it with Hitachi pneumatic tool lubricant. Lubricate it with Hitachi pneumatic tool lubricant. Correct the deformation. 6 In case of the feeder and shafts. Knob 1 Disconnect air hose Nail Guide 3 Open the nail guide and remove dust. ...nippers. Nose Push Lever 1 Disconnect air hose Lubricate 3. Nail Slotted Screw Driver 5 Cut the deformed collated wire with a hammer. and 2) clearing a jam. 1. Hammer rod 2. CAUTION ⅷ Check that differ from Nailer when: 1) doing maintenance and inspection; WARNING ⅷ Disconnect air hose and remove all nails from...