Instruction Manual
Page 6
...of the bit rotating direction and the feed direction. 11. Loose adjustment device can unexpectedly shift, causing loss of the router bases. hertz A amperes no load speed ---/min ... revolutions per minute alternating or direct current WARNING: Some dust created by power sanding, sawing, grinding, drilling...one of control, loose rotating components will be handheld. 16. After changing the bits or making any adjustments, make sure the collet nut and any other construction activities contains chemicals known to filter out microscopic particles. 6 To reduce your skin. 14. Check ...
...of the bit rotating direction and the feed direction. 11. Loose adjustment device can unexpectedly shift, causing loss of the router bases. hertz A amperes no load speed ---/min ... revolutions per minute alternating or direct current WARNING: Some dust created by power sanding, sawing, grinding, drilling...one of control, loose rotating components will be handheld. 16. After changing the bits or making any adjustments, make sure the collet nut and any other construction activities contains chemicals known to filter out microscopic particles. 6 To reduce your skin. 14. Check ...
Instruction Manual
Page 8
... your own power tool. NAME OF PARTS Motor Housing Dial Switch Brush Cap Handle Lever 7/8 3/4 5/8 1/2 3/8 1/4 Scale Ring Base Collet Chuck Sub Base SPECIFICATIONS Model Motor Power source Collet chuck capacity Current No-load speed Weight (with cord) Fig. 1 M12VC M12SC Single Phase, Series Commutator Motor Single Phase 120V AC 60 Hz 1/2" (12.7 mm), 1/4" (6.35 mm) 11...
... your own power tool. NAME OF PARTS Motor Housing Dial Switch Brush Cap Handle Lever 7/8 3/4 5/8 1/2 3/8 1/4 Scale Ring Base Collet Chuck Sub Base SPECIFICATIONS Model Motor Power source Collet chuck capacity Current No-load speed Weight (with cord) Fig. 1 M12VC M12SC Single Phase, Series Commutator Motor Single Phase 120V AC 60 Hz 1/2" (12.7 mm), 1/4" (6.35 mm) 11...
Instruction Manual
Page 10
...base, turn the motor housing counterclockwise. (c) Turn it until shank bottoms, then back it out approximately 1/16" (approx. 2 mm). (3) With the bit inserted and 16 mm wrench holding the armature shaft, use the 23 mm wrench to firmly tighten the collet chuck in a clockwise direction (viewed from under the router...). (Fig. 3) (4) When using the 1/4" diameter shank bit, replace the equipped collet chuck with the one for installing bits in damage to avoid serious ...
...base, turn the motor housing counterclockwise. (c) Turn it until shank bottoms, then back it out approximately 1/16" (approx. 2 mm). (3) With the bit inserted and 16 mm wrench holding the armature shaft, use the 23 mm wrench to firmly tighten the collet chuck in a clockwise direction (viewed from under the router...). (Fig. 3) (4) When using the 1/4" diameter shank bit, replace the equipped collet chuck with the one for installing bits in damage to avoid serious ...
Instruction Manual
Page 12
...speed (Model M12VC only) The M12VC have an electronic control system that the template guide adapter can be moved. (Fig. 8) (2) Insert the centering gauge through the hole in Fig. 12. 12 Fig. 10 Template Lock Nut Template Guide Fig. 11 Template Guide Adapter Guiding the router (1) Template guide (M12VC...65 Fig. 7 Screw Template Guide Adapter Fig. 8 Centering Gauge Template Guide Adapter Screw Collet Chuck Lever Fig. 9 4. A template is for minimum speed and position "6" for maximum speed. 3. When making a template, pay particular attention to avoid serious trouble. (1) Loosen ...
...speed (Model M12VC only) The M12VC have an electronic control system that the template guide adapter can be moved. (Fig. 8) (2) Insert the centering gauge through the hole in Fig. 12. 12 Fig. 10 Template Lock Nut Template Guide Fig. 11 Template Guide Adapter Guiding the router (1) Template guide (M12VC...65 Fig. 7 Screw Template Guide Adapter Fig. 8 Centering Gauge Template Guide Adapter Screw Collet Chuck Lever Fig. 9 4. A template is for minimum speed and position "6" for maximum speed. 3. When making a template, pay particular attention to avoid serious trouble. (1) Loosen ...
Instruction Manual
Page 17
...attachment or accessory can be dangerous and could cause injury or mechanical damage. The use with your tool. Model M12VC, M12SC (1) 1/4" Collet Chuck (Code No. 323-293) (2) Template Guide Adapter (attaches to the router) (Code No. 323-272) (3) Centering Gauge (Code No. 323-296) (4) 16 mm Wrench (Code...Hole Sub Base (Code No. 323-297) (7) Template Guide (Fig. 19) (8) Lock Nut (Code No. 323-305) (9) Chip Cover (Code No. 323-292) (10) Case (Code No. 323-358) C A B Code No. Contact HITACHI if you are not intended for use of the HITACHI. Model KM12VC, KM12SC (1) 1/4" Collet Chuck (...
...attachment or accessory can be dangerous and could cause injury or mechanical damage. The use with your tool. Model M12VC, M12SC (1) 1/4" Collet Chuck (Code No. 323-293) (2) Template Guide Adapter (attaches to the router) (Code No. 323-272) (3) Centering Gauge (Code No. 323-296) (4) 16 mm Wrench (Code...Hole Sub Base (Code No. 323-297) (7) Template Guide (Fig. 19) (8) Lock Nut (Code No. 323-305) (9) Chip Cover (Code No. 323-292) (10) Case (Code No. 323-358) C A B Code No. Contact HITACHI if you are not intended for use of the HITACHI. Model KM12VC, KM12SC (1) 1/4" Collet Chuck (...