Hitachi 6.2Amp - D13 1/2" Electric Drill Rev. D-Handle 55 Support and Manuals
Get Help and Manuals for this Hitachi item
This item is in your list!
View All Support Options Below
Free Hitachi 6.2Amp manuals!
Problems with Hitachi 6.2Amp?
Ask a Question
Free Hitachi 6.2Amp manuals!
Problems with Hitachi 6.2Amp?
Ask a Question
Popular Hitachi 6.2Amp Manual Pages
Instruction Manual - Page 1
HITACHI
DRILL MODEL D 13
INSTRUCTION MANUAL
Note: Before using this INSTRUCTION MANUAL to ensure efficient, safe operation. It is recommended that this MANUAL be kept readily available as an important reference when using this Electric Power Tool, carefully read through this electric power tool.
0 DOUBLE INSULATION
Instruction Manual - Page 2
...should be kept away from work area well lit. Don't use tool in moving parts.
All visitors should also wear safety eye protectors and face or dust masks.
2... INSTRUCTIONS
1. Do not wear loose clothing or jewelry. We sincerely thank you for selecting a HITACHI ELECTRIC POWER TOOL. To operate this electric power tool safely and efficiently, please read this INSTRUCTION MANUAL carefully...
Instruction Manual - Page 3
... for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other...replaced by authorized service facility. Inspect tool cords periodically and if damaged, have repaired by authorized service center. DISCONNECT TOOLS. otherwise, a hazardous condition may affect its intended function. 10. DON'T OVERREACH. Don't carry plugged-in this instruction manual...
Instruction Manual - Page 4
....
28. STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS DETECTED. DO NOT WIPE PLASTIC PARTS WITH SOLVENT. SERVICE AND REPAIRS
All qualitytools will eventually require servicing or replacement of order or should ONLY be observed during operation, stop .
31. In such cases, metal parts could become electrically live wiring may lead to become clogged up, even if...
Instruction Manual - Page 5
...14
12
Not Recommended
5 Table shows the correct size to install the proper outlet. The smaller the gage number, the ...in the outlet, reverse the plug. MINIMUM GAGE FOR CORD SETS
Total Length of Cord in loss of electric shock, this ...to use only identical replacement parts. POLARIZED PLUGS
To reduce the risk of power and overheating. REPLACEMENT PARTS
When servicing use one way. ...
Instruction Manual - Page 6
... and both the
" " mark and "Double insulation", or either one is required with wrong parts may result in this manual must still
DOUBLE INSULATION
be followed. Always contact your dealer or an authorized HITACHI service agent when
assembling, disassembling or replacing parts other than accessories or carbon
brushes. Attach the side handle and hold the drill...
Instruction Manual - Page 7
... power supply. PREPARATION PRIOR TO OPERATION
Before using the Electric Power Tool, complete the following preparations. 1. NAME OF PARTS
Drill Chuck
Gear Cover r
l Sri Name Plate Brush Cap
Bolt
Switch Trigger Im
Stopper
SPECIFICATIONS
Motor Power Source Current Capacity No-load Speed Weight
Fig. 1
Single-Phase, Series Commutator Motor Single-Phase 115V...
Instruction Manual - Page 8
...set to prescribed precautions. There are three holes in which the chuck wrench should be removed in the voltage specified on the back of the drill. The drill bits can be replaced or repaired...the reversing
switch is set to the "Fr position, and rotates
oom
in lumber Use woodworking drill bits. CAUTION: Damaged cord must be installed on the name plate.
2. Installing spade handle The ...
Instruction Manual - Page 9
...drilling depth is useful for repair service. If such a faulty receptacle is important to break the drill bits when penetrating.
Operation of the drill.
2.
Installing the depth stopper (optional ... cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpen without delay when abrasion is rotating. Install the depth stopper to switch power OFF...
Instruction Manual - Page 10
... holders. of research and development, the specifications herein are worn down to the limit line, replace the brushes with new ones, be kept...trouble may cause a hazardous situation.
3. 2. Loosened screws, if unheeded, may result.
of carbon brush
0.67" (17mm)
Fig. 4
NOTE: Due to the illustrated number. When replacing the brushes with new ones. If any screws are consumable parts...
Parts List - Page 1
HITACHI
LIST NO. 0145
ELECTRIC TOOL PARTS LIST
• DRILL Model D 13
1997 3 10 (E5)
1 58
••
2C 2A 3B
3A
7,
6
I
7
9 10
40 39
13 14
C
21
CD
23A 24
26 28A
29
27
30
31
C
33
4 44 43 42 41
39
t
54 52 51 50 49
48
56 57 57A
36 37
Parts List - Page 2
... - SOCKET SET SCREW M4X6
2 SINCE 3.1986
36 982- 794Z I INNER COVER ASS'Y
1 INCLUD.14,16,17
16 984- 357 WASHER -
1
17 609- TYPE HANDLE
- 2-
1 *: ALTERNATIVE PARTS
3-97 SUI...981- 657F ARMATURE 240V
1
18 982-807 ARMATURE 100V
1 FOR KOR
19 981- 562 FAN GUIDE
1
21 931- 875 TAPPING SCREW D5X35
2
22A 991- 007 TAPPING SCREW D5X60
2
23A ...GEAR
1
11 627-
PARTS
ITEM
N
CODE NO.
Parts List - Page 3
...STOPPER
NO. USED
1
1
3-97
* : ALTERNATIVE PARTS
REMARKS
- 3- PARTS
ITEM N
CODE NO.
37 982-796Z
38 937-807
39 949...- 360 HANDLE (A) 48 982-095 TAPPING SCREW (W/WASHER) D4X20 49 930- 153 SUPPORT (B)
50 994- 273 NOISE SUPPRESSOR 50 971- 828 NOISE SUPPRESSOR 51 930-446 ....) 53 961-419Z TERMINAL 54 960- 266 CORD CLIP 55 957-561 HITACHI LABEL 56 953- 327 CORD ARMOR D8.8 56 938-051 CORD ARMOR ...
Specifications - Page 1
Couper Ici
1/2" Drill, 550 RPM
D13
Specifications
Capacities
>> AMP:
6.2
>> Steel:
1/2"
>> RPM: >> Max Torque: >> Chuck:
550 477.4 in-lbs. 1/2"
>> Wood: >> Hole Saw:
1/5/8" 4-1/8"
>> Weight:
7 lbs
Notes: Powerful 6.2 AMP motor.
S.V.P. Couper Ici / Please Cut Here
Please Cut Here / S.V.P. Auto-stop carbon brushes protect armature
and extend tool life. Industrial...
Hitachi 6.2Amp Reviews
Do you have an experience with the Hitachi 6.2Amp that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hitachi yet.
Earn 750 points for your review!