HP J4902A Support and Manuals
HP J4902A Videos
Popular HP J4902A Manual Pages
User Manual - Page 1
installation and getting started guide
hp procurve switch 6108
www.hp.com/go/hpprocurve
User Manual - Page 4
...Switch 6108 (J4902A)
Disclaimer
The information contained in this material.
Hewlett-Packard shall not be obtained from your HP Sales and Service Office or authorized dealer.
Warranty
See the Customer Support/Warranty booklet included with the furnishing, performance, or use or reliability of its software on equipment that is subject to your Hewlett-Packard products and replacement parts...
User Manual - Page 6
... 4-9
Testing the Switch by Resetting It 4-9 Checking the Switch LEDs 4-9 Checking Console Messages 4-9
Testing Twisted-Pair Cabling 4-10 Testing Switch-to-Device Network Communications 4-10 Testing End-to-End Network Communications 4-10 Restoring the Factory Default Configuration 4-11 Downloading New Switch Software 4-12 HP Customer Support Services 4-12 Before Calling Support 4-12
ii
User Manual - Page 9
HP Procurve Switch 6108 (HPJ4902A)
Throughout this manual, this switch and connect the switch to a network backbone or to the desktop. In addition, the Switch 6108 offers full network management capabilities. This chapter describes your HP Switch 6108 including: ■ Front and back of the switch ■ Switch features
1-1 The Switch 6108 has six auto-sensing 10/100/1000Base-T RJ-45 ports ...
User Manual - Page 14
... configuration and operation, you should make sure the switch is installed in a specific pattern, any configuration changes you are concerned with the Reset button in a secure location, such as a locked wiring closet.
■ Restoring Factory Default Configuration - This action clears any temporary error conditions that may have misplaced the password and need console access. This button is...
User Manual - Page 17
...Included Parts
The Switch 6108 has the following components shipped with it:
■ HP Procurve Switch 6108 Installation and Getting Started Guide (J4902-90001), this manual
■ HP Procurve Product Documentation CD ROM (contains PDF file copies of the documentation for the Switch 6108, including the Management and Configuration Guide, and for most other HP Procurve switches)
■ HP...
User Manual - Page 19
...cord displaying the mark of the safety agency that the switch does not overload the power circuits, wiring, and over . The mark is not restricted.
2-3 Installing the Switch 6108
Warning Cautions
Installing the Switch 6108 Installation Procedures
Installation Precautions:
Follow these precautions when installing your HP Switch 6108.
■ The rack or cabinet should be adequately secured to...
User Manual - Page 21
... this manual was printed, the supported mini-GBICs include the following: ■ HP Procurve Gigabit-SX-LC mini-GBIC (J4858A) ■ HP Procurve Gigabit-LX-LC mini-GBIC (J4859A) ■ HP Procurve Gigabit-LH-LC mini-GBIC (J4860A)
The HP Procurve mini-GBICs are shared with two of the switch, leave at least 7.6 cm (3 inches) for cooling, except if the switch is installed...
User Manual - Page 33
...Documentation CD-ROM that came with the Switch 6108. (If your switch.
2-17 For more detailed information, refer to continue with the switch
PC running a terminal emulator program, or
a VT-100 terminal
hp procurve switch 6108
J4902A
Power Fault
Console
Reset Clear
3. Installing the Switch 6108
Installing the Switch 6108 Installation Procedures
Direct Console Access
To connect a console...
User Manual - Page 40
... and password protection in the preceding section, connect a terminal device to the switch, start a console session, and access the Switch Setup screen.
1. The CLI prompt appears displaying the switch model number: HP Procurve Switch 6108#
2.
The following illustration shows the Setup screen with your network is on the Documentation CD-ROM that came with the default settings.
User Manual - Page 43
... interface that point in the command entry. Entering any command followed by running the Telnet session (for example:
HP Procurve Switch 6108# Enter help information about the command.
No additional software installation is required to manage the switch from any PC that is on the network by help provides more detailed context help or ? You will...
User Manual - Page 49
...-GBICs will be replaced.
plugged into a different outlet or try a different power cord.
Then, reset the switch.
If the Power LED is still not on, verify that it is
powered on indefinitely.
➌ The switch has 1.
Troubleshooting
4-5 If necessary to resolve the problem, contact your HP-authorized LAN dealer, or use the electronic support
services from HP to get...
User Manual - Page 53
... Main Menu.
4-9
Troubleshooting
See "Diagnosing With the LEDs" on page 4-4 for information on longer than 60 seconds or begin blinking, there may be displayed on self test, which can reset the switch to be a problem with the other terminal communication settings shown on the front of the switch Power cycling the switch and pressing the Reset button both...
User Manual - Page 55
... begin operating with your troubleshooting process on the Switch 6108, it may result in network connectivity issues. To execute the factory default reset on the switch itself, or through the switch console. This process momentarily interrupts the switch operation, clears any passwords, clears the console event log, resets the network counters to the factory default settings. Using pointed...
User Manual - Page 80
... 1000Base-SX ... Index C-8 environmental specifications, switch ... B-5 cabling infrastructure ... 2-4 Clear button
deleting passwords ... 1-6 description ... 1-6 location on switch ... 1-2, 1-6 restoring factory default configuration ... 1-6,
4-11 to delete password protection ... 3-4 CLI prompt, console displaying ... 2-17 configuration checking when troubleshooting ... 4-3 DHCP/Bootp...
HP J4902A Reviews
Do you have an experience with the HP J4902A that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!