Harbor Freight Tools 99612 - LED Air Angle Die Grinder Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 99612 manuals!
Problems with Harbor Freight Tools 99612?
Ask a Question
Free Harbor Freight Tools 99612 manuals!
Problems with Harbor Freight Tools 99612?
Ask a Question
Popular Harbor Freight Tools 99612 Manual Pages
User Manual - Page 1
... GRINDER
99612
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®. Copyright© 2008 by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product. All rights reserved. L.E.D. For technical questions or replacement parts, please...
User Manual - Page 2
.... Do not use common sense when operating this Die Grinder. Safety Alert Symbol and Signal Words
In this manual, on the labeling, and all safety messages that follow this manual for future reference. IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF INJURY TO PERSONS
WARNING - To reduce the risks of control. Write the product...
User Manual - Page 3
... storing.
c.
Disconnect the Die Grinder from moving parts.
longed exposure to high
intensity noise is able ..., or medication. Dress properly. way to secure and support the
Loose clothes, jewelry, or long hair
workpiece to... situations. Use safety equipment.
shoes and a hard hat must be repaired.
e.
f. Maintain the tool with the Control Lever (4) depressed. ...
User Manual - Page 4
... SPECIFIC SAFETY
INSTRUCTIONS
Symbol Definitions
Symbol Property or statement
no .../min
No-load speed
Revolutions or reciprocation per minute
PSI Pounds per square inch of pressure
ft-lb Foot-pounds of injury to this Die Grinder must be performed only by poorly maintained tools.
When servicing this tool's operation.
Check for the specific tool model...
User Manual - Page 5
...the
cussed in this tool during set up and use with accessories rated ...to at least 20,000 RPM.
Moving parts can
birth defects or other reproductive
result... product, but
8.
Obey the manual for the forces gener-
3. Install an in an emergency, even ...or statement
Code § 25249.5, et seq.)
WARNING marking concerning Risk of California
Specific Safety Instructions
to allow...
User Manual - Page 6
...problems are not being caused or worsened from
Maximum Air Pressure
90 PSI
use.
Grip tool as lightly as explained in this tool. Let
the tool do the work .
6. Specifications...keeping safe control of it). Do not smoke during use this manual.
Maximum Speed*
20,000 RPM
vous system disorders, diabetes, ...INSTRUCTIONS. Components and Controls
3.
SKU 99612
For technical questions, please call...
User Manual - Page 7
...this manual. Remove this tool. An in the diagram above.
If any other bottled gas as a power source for best service, as...install a female quick coupler on the tool. Such a coupler contains an air valve that the item is ruptured. Add a few drops of this manual including all text under subheadings therein before set up or use .
2. Note: For additional information regarding the parts...
User Manual - Page 8
...refer to Operation section for damaged, loose, and missing parts. Inspect tool before use of controls.
NOTE: Grinding...manual. OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section including all text under subheadings therein before set ...not specifically explained within this time, turn off position; Adjust the pressure gradually, to set up pressure until repaired....
User Manual - Page 9
... included) to reach the work area that has the correct diameter (either 1/4" or 1/8"). Grinding Attachment Installation 6.
1. Select the Collet (31) that is clean and well-lit. Route the air hose along...the Chuck Casing (29) a few turns. Switch (ON/OFF) (37)
Work Piece and Work Area Set Up
1.
Insert the Collet (31) into the Clamp Nut (32). Designate a work area without creating ...
User Manual - Page 10
...more
with air supply. Problem
Die Grinder
Possible Causes
1. Check air hoses and replace
4. Do not use...repair air hoses. 2. Allow the grinding attachment (not included) to accomplish the task,
enough
more after each
7.
General Operating Instructions...are grinding. Grinding attachment is a premium, switch on
TROUBLE SHOOTING
the LED Light (38) by squeezing the Control...
User Manual - Page 11
...If the Vanes (19) need replacement, all vanes should be replaced as part of the regular operation of ...INSTRUCTIONS
Procedures not specifically explained in addition to the regular checks and maintenance explained as a set.
If abnormal noise, vibration, or leaking air occurs, have the problem...Lubrication
Note: These procedures are in this manual must be regularly drained. The lubricator's oil...
User Manual - Page 12
... AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Replace the Switch (37) by threading it...
User Manual - Page 14
... specific ...repairs or alterations outside our facilities, criminal activity, improper installation..., normal wear and tear, or to lack of exclusion may elect to refund the purchase price if we determine there is no defect, or that this warranty, the product or part...repaired products at our election or we may not apply to us with a replacement. We will either repair or replace...
Harbor Freight Tools 99612 Reviews
We have not received any reviews for Harbor Freight Tools yet.