Harbor Freight Tools 61932 - Cement Mixer - 3-1/2 Cubic Ft Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 61932 manuals!
Problems with Harbor Freight Tools 61932?
Ask a Question
Free Harbor Freight Tools 61932 manuals!
Problems with Harbor Freight Tools 61932?
Ask a Question
Most Recent Harbor Freight Tools 61932 Questions
Sheer Pin On The Cement Mixer?
If there is one, where is this located?
If there is one, where is this located?
(Posted by djholmes0928 1 year ago)
Bought 3.5 Cubic Ft. Cement Mixer, Missing Belts How Can I Get The Belts To
(Posted by udenkwo 1 year ago)
Bolts For Mixer?
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
(Posted by chrstphr1grffn 1 year ago)
Assemble Help
I bought this machine. How do I put it together?Is there a video? Is there a video?Serial # 19317532...
I bought this machine. How do I put it together?Is there a video? Is there a video?Serial # 19317532...
(Posted by simmonsbert2 1 year ago)
Popular Harbor Freight Tools 61932 Manual Pages
User Manual - Page 2
... 61932 Safety
NOTICE
FOR CEMENT AND MORTAR ONLY. Obey all safety messages that follow this symbol to personal injury.
Table of Contents
Safetye 3 Specifications 6 Setup 7 Operationa 10
Maintenancei 12 Parts List and Diagram 14 Warranty 16
WARNING SYMBOLS AND DEFINITIONS This is used to alert you to potential personal injury hazards.
It is...
User Manual - Page 3
... a replacement. Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY.
Do not use power tools in loss of the area during assembly.
3.
IMPORTANT SAFETY INFORMATION
WARNING Read all warnings and instructions for which it comes to use ; Failure to play with Epoxy 2-part...
User Manual - Page 4
...installed by a qualified electrician. The tool must never be attached to a properly grounded outlet. Safety
Setup
Grounding
NOTICE
FOR CEMENT AND MORTAR ONLY.
Tools marked with Epoxy 2-part... cord.
2. Always replace a damaged extension cord or have it repaired by a qualified electrician... all codes and ordinances. If damaged, have it repaired by a service facility before using ...
User Manual - Page 5
...-
-
* Based on this instruction manual cannot cover all possible conditions and...specific...Setup...Code § 25249.5, et seq.)
10.
Industrial applications must be supplied by an appropriate standards agency. Page 5 When servicing use .
Unapproved safety equipment may occur. The warnings, precautions, and instructions discussed in the work before use only identical replacement parts...
User Manual - Page 6
... Nicotine reduces the blood supply to ensure medical problems are not being caused or worsened from use this manual.
Specifications
Electrical Input Motor No Load Speed Drum Speed Drum...Setup
Operation
Maintenance
Page 6
For technical questions, please call 1-888-866-5797. Anyone using vibrating tools regularly or for an extended period should not use . Use tools with Epoxy 2-part...
User Manual - Page 7
...and Hex Flange Nuts (5). Tighten with a wrench until secure.
3. Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY. Hex Bolts (69), Flat Washer (...(78) into Stand so that bolt holes line up .
4. Note: Set Stand on its side for easier assembly.
Insert Leg (79) into the... at the beginning of this manual.
Note: For additional information regarding the parts listed in the following pages,...
User Manual - Page 8
...part resin mix.
8. Arm (77)
Figure D
9. Mount Handle Control Plate (41) to a point where the Arm (77) can still move. 12. See Figure E. Tighten connections until secure.
10. Tighten to Support... Drum (48)
16. With assistance, set the Lower Drum (48) with wrench ...Support Bracket Seat (35) using Hex Bolts (54), Washers (55), Seal Gaskets (56), and Hex Flange Nuts (5).
Safety
Setup...
User Manual - Page 9
...to the Switch (13) does not come in all four Hex Nuts since the motor will be flush with Epoxy 2-part resin mix.
21. Check all screws, nuts, and bolts are securely tightened. Do not use a hex key (not...should be adjusted forward or backward later.
26. When proper V-Belt tension is tight. Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797.
User Manual - Page 10
...
Lower Drum Arm
Leg
Handle Control
Plate
Setup
Operation
Maintenance
Page 10
For technical questions, please call 1-888-866-5797. Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use with Epoxy 2-part resin mix.
Safety
NOTICE
FOR CEMENT...
User Manual - Page 11
... with Epoxy 2-part resin mix. ... Drum is rotating. Do not turn Mixer off while full of children's reach. Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Do...finished, flip the Switch to move the Cement Mixer when it is reached. General Operating Instructions
1.
Do not use with wheel chocks (not included).
2. Safety
NOTICE
FOR CEMENT ...
User Manual - Page 12
...problem corrected before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the Drum with Epoxy 2-part... replaced only by a qualified service ...Servicing
Procedures not specifically ...Setup
NOTICE
FOR CEMENT AND...manual must be performed only by loosening the Motor Bracket bolts and moving parts
• Cracked or broken parts...
User Manual - Page 13
... small. Have technician service tool. Disconnect power supply before service. Likely Solutions
1. Internal damage or wear. If an extension cord is needed , use with the proper diameter for the tool and circuit has no -load intervals.
2. Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Safety
Troubleshooting
NOTICE
FOR CEMENT...
User Manual - Page 14
Do not use with Epoxy 2-part resin mix. Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY.
Parts List and Diagram
Parts List
Part
Description
1 Cotter Pin 5×40
2 Flat Washer 27
3 Wheel
...30 Flat Washer 8
31 Motor Hood
32 Nut M6
33 Bearing 6002ZZ
34 Ring Shield Ø38
35 Support Bracket Seat
36 Pinion Shaft
37 Gear
38 Flat Key 5×12
39 Gear Cover
40 Cross-Head Screw...
User Manual - Page 15
...for illustration purposes only, and are not available individually as replacement parts.
Item 61932
For technical questions, please call 1-888-866-5797. Do not use with Epoxy 2-part resin mix.
Safety
16 1110 14 15
13
12 ...10 11 10 9 8
10
17
1821
7
22 2324
18 20 1917
6
59
60
5
25
54
Setup
55
56
5
56 61...
User Manual - Page 16
...BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. We shall in materials and workmanship for incidental, contingent, ...the date of returning the product. This warranty gives you specific legal rights and you with transportation charges prepaid.
Harbor Freight Tools 61932 Reviews
We have not received any reviews for Harbor Freight Tools yet.