Haier HWM90-98 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier HWM90-98 manuals!
Problems with Haier HWM90-98?
Ask a Question
Free Haier HWM90-98 manuals!
Problems with Haier HWM90-98?
Ask a Question
Popular Haier HWM90-98 Manual Pages
User Manual - Page 1
... those risks occurred from not obeying this manual carefully before using to question 16
Packing list 17
Specification table
The back cover The manufacturer will not bear the responsibility for future reference
Please check if the power receptacle has good earthing condition before using. User's manual
HWM90-98
Computerized Full-auto Washing Machine
Please read...
User Manual - Page 3
... the pin of our special shop or the after-sale service department.
Do not wash water-proof laundries like the bathroom... or nip it replaced by the technicians of the power plug clean,if the power plug is installed on the control panel...abnormal vibrations in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine.
In case the washing...
User Manual - Page 4
... take out all of our company.
Dismantle
Install
To prevent your pocket, such as thinner, petrol etc.). Benzene
The appliance is connected properly. Before washing, please check if the water tap is open, and if the water inlet pipe is not instruct for use low-foaming washing powder.
2
The lint filter shall...
User Manual - Page 5
... outer tub cover shaft groove. Loosen High
adjustable nut Fasten
adjustable foot Low
3 Please install to designated position to guarantee there are no dropping or abnormal sound in unstable running or...front of the cabinet (front the sight of the manual. See to the figure:
Back Front Bottom plate Screw Soft items
Adjust the Installation position
The largest allowed slope of the shank base...
User Manual - Page 7
... face of the lock lever and push down the slider. See to Figure 1.
2 Loosen the screw till the water faucet can not be set on the faucet. Install the water inlet hose Before Using
Confirm the water faucet
water faucet, suitable
The exit end face of the faucet
water faucet, not suitable...
User Manual - Page 8
... 's suitable. Dismantle the water inlet hose
1. Locking level Slider
Remarks: use the new hose sets supplied with overstrain.
4.Before each usage.
Close the water faucet.
2. Push down the slider. If the machine is fastened stable. 2.After installation, open the faucet to check if it gently to the jointer.
Then pull of the...
User Manual - Page 9
... and loosen the
laundries before
putting them in advance, which can make it over before putting in
the tub. b. For those with machine. For the parts with heavy soil, please first remove the dirt like mud or dust. Do not put the laundries with hand.
Divide the laundries that are applicable...
User Manual - Page 12
...machine have no reaction.
During common and carpeting programs, push the SPIN/DISINFCT button to set different spin time (from 0 to 25 minutes) During normal ,cotton woollen and silk ...tube corresponding to the running program lights.
During standard and jeans programs, push the SOAK button to set different rinse times ( 0, 1, 2, 3, 4 times) During normal , cotton woollen and silk ...
User Manual - Page 13
...Reserve/remain time indicator digitron
During sensing, it reaches the overflow water level, the machine will set water level by yourself.
You shall push the START/PAUSE button to Page 16)
Page 16... and SPIN button at tens place to represent 100 minutes, b to add water. You must set water level automatically.
If there's water inside the tub, the machine cannot detect the laundries and...
User Manual - Page 14
... "program button" on the power.
MINUTES MINUTES
TIMES
MINUTES
SOAK
WASH
RINSE SPIN/DISINFECT
12 Page 11
In selecting the normal program, the machine will set normal program automatically. Using process
Steps of using the operation buttons and description of the laundries.
PROGRAM
After switching on . For instance: select "POSTHASTE" program...
User Manual - Page 15
... select other laundries in other cases. Page 9
Page 11
Water Level and Time Table for selection.
The soak program can set to set the program and procedure during washing, and can not make setting in washing. When you select to water level 3. Even there's no water in softener. If you don't select to...
User Manual - Page 16
..., the machine will be finished after 18 hours.
the time displayed on spin digitron is set the reserve wash program. If you need to off the power automatically.
Page Confirm the ... time) * In selecting "posthaste" program, the washing machine will set the complete procedures of the program you need to set the washing
procedure to be influenced by the water inlet pressure and water...
User Manual - Page 17
...lid for a long period. Otherwise it with brush every two months. Dismantle
Install
Dismantle
Install
Install
Dismantle
Dismantle and install
Clean
The filter screen of the water inlet valve is dirty, wipe it ... up aslant and gently. 2.The method of install : install it upwards and aslant
and push it with water.
Clean the detergent box and set it on the surface of the lint filter ...
User Manual - Page 18
...level reached preset position? Are the laundries set flat? There's abnormal sound inside the ... special maintenance department or after -sales service department.
Adjust the machine to be some... off the power plug before it to repair. Fill water to the preset position....placed horizontally. Are the laundries put slantingly? Trouble-shooting answer to question
(If there's breakdown,...
User Manual - Page 20
...~0.78MPa 380W 300W About 39kg
L 610 mm W 580mm H 975 mm Specification table
Model Rated voltage frequency Rated washing / spinning capacity Water level/Water quantity (about)
Max water consumption Water Injection pressure Rated washing input power Rated spinning input power Weight Overall dimension
HWM90-98 220V-240V ~ 50Hz 9.0kg 1/18L 2/24L 3/30L 4/36L 5/42L 6/48L...
Haier HWM90-98 Reviews
We have not received any reviews for Haier yet.