Installation Instructions
Page 1
Installation Instructions Addendum These instructions are needed to install an icemaker in the models listed below. Keep this addendum with an IM4, IM4A or IM6 Icemaker Kit. GBS20KBP GBS22HBP GBS22KBP PDS20MBP PDS20SBP PDS22MBP PDS22SBP 197D5736P001 49-60286-3 06-03 JR To be used with your refrigerator. Icemaker Accessory Kit Addendum for IM4, IM4A and IM6 Icemaker Kits www.GEAppliances.com IMPORTANT: These instructions are to be used to install an Icemaker Kit in your Owner's Manual and Installation Instructions.
Installation Instructions Addendum These instructions are needed to install an icemaker in the models listed below. Keep this addendum with an IM4, IM4A or IM6 Icemaker Kit. GBS20KBP GBS22HBP GBS22KBP PDS20MBP PDS20SBP PDS22MBP PDS22SBP 197D5736P001 49-60286-3 06-03 JR To be used with your refrigerator. Icemaker Accessory Kit Addendum for IM4, IM4A and IM6 Icemaker Kits www.GEAppliances.com IMPORTANT: These instructions are to be used to install an Icemaker Kit in your Owner's Manual and Installation Instructions.
Installation Instructions
Page 2
....2002 and order part WR02X11712. If the ground wire is missing from the kit that will be needed to install the icemaker. 1 Icemaker InInsstatrlulacttiioonns 2 Owner's Manual & Installation Instructions 3 Water Valve and Tube Assembly 5 Hex-Head Screw for Water Line Clamp 6 Water Line Clamp (...strain relief), for house water line ICEMAKER WARRANTY VERIFICATION Date Installed Dealer 7 Warranty Label 8 Hex-Head Screw, for attaching water valve 9 Phillips Head Screws, for mounting icemaker (2) 10 Water Tube Inlet 11 Icemaker Fill Cup (side-mounted) 12 Hose Clamp 4 Adhesive...
....2002 and order part WR02X11712. If the ground wire is missing from the kit that will be needed to install the icemaker. 1 Icemaker InInsstatrlulacttiioonns 2 Owner's Manual & Installation Instructions 3 Water Valve and Tube Assembly 5 Hex-Head Screw for Water Line Clamp 6 Water Line Clamp (...strain relief), for house water line ICEMAKER WARRANTY VERIFICATION Date Installed Dealer 7 Warranty Label 8 Hex-Head Screw, for attaching water valve 9 Phillips Head Screws, for mounting icemaker (2) 10 Water Tube Inlet 11 Icemaker Fill Cup (side-mounted) 12 Hose Clamp 4 Adhesive...
Installation Instructions
Page 3
... it and rotating its bottom to prevent premature operation. TOOLS YOU WILL NEED Flat blade and Phillips Pliers screwdrivers Sharp knife 1 PREPARE FOR INSTALLATION • Remove the storage basket (on some models) by pulling it out and lifting it up and out. Power Switch 3 Note:...the stop position and lifting it to the refrigerator. 3 SET POWER SWITCH TO O (off) Set the icemaker power switch to the back of the refrigerator. Unplug the Refrigerator. cover 2 INSTALL FILL TUBE • Slide the fill tube shipped with a flat-blade Outlet screwdriver. Leave the power ...
... it and rotating its bottom to prevent premature operation. TOOLS YOU WILL NEED Flat blade and Phillips Pliers screwdrivers Sharp knife 1 PREPARE FOR INSTALLATION • Remove the storage basket (on some models) by pulling it out and lifting it up and out. Power Switch 3 Note:...the stop position and lifting it to the refrigerator. 3 SET POWER SWITCH TO O (off) Set the icemaker power switch to the back of the refrigerator. Unplug the Refrigerator. cover 2 INSTALL FILL TUBE • Slide the fill tube shipped with a flat-blade Outlet screwdriver. Leave the power ...
Installation Instructions
Page 4
... are already in place in the freezer side wall. • Install two self-tapping Phillips head screws (9) from the side wall. 5 INSTALL THE ICEMAKER FILL CUP Install the icemaker fill cup (side-mounted) (11) into the icemaker as shown. 11 7 MOUNT THE ICEMAKER • Lift the icemaker so the fill tube shipped with this addendum with your Refrigerator...
... are already in place in the freezer side wall. • Install two self-tapping Phillips head screws (9) from the side wall. 5 INSTALL THE ICEMAKER FILL CUP Install the icemaker fill cup (side-mounted) (11) into the icemaker as shown. 11 7 MOUNT THE ICEMAKER • Lift the icemaker so the fill tube shipped with this addendum with your Refrigerator...
Installation Instructions
Page 5
... VALVE ASSEMBLY INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN Read each step thoroughly before proceeding. • CAUTION - Either wire can go on the water valve (3). Cabinet 8 Water valve bracket Hex-... blade and Phillips screwdrivers Pliers Sharp knife 1/4″ and 5/16″ Nutdrivers Tape measure 1 REMOVE THE COVER At the bottom rear of electric shock during installation, you must be reinstalled later to the water valve. Unplug the Refrigerator. Bend the cover back to the cabinet by driving the hex-head screw...
... VALVE ASSEMBLY INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN Read each step thoroughly before proceeding. • CAUTION - Either wire can go on the water valve (3). Cabinet 8 Water valve bracket Hex-... blade and Phillips screwdrivers Pliers Sharp knife 1/4″ and 5/16″ Nutdrivers Tape measure 1 REMOVE THE COVER At the bottom rear of electric shock during installation, you must be reinstalled later to the water valve. Unplug the Refrigerator. Bend the cover back to the cabinet by driving the hex-head screw...
Installation Instructions
Page 6
...: To ensure a proper ground, the end of the ground wire MUST be used for the house water line (see Water Line Installation Instructions). To make sure the icemaker is not to be secured to the refrigerator cabinet. 4 CONNECT WATER TUBE TO INLET • Squeeze the ends of the hose ... the screw (5) from the kit to the refrigerator. With the clamp directly in line with three of the freezer. Note: After installing the icemaker, do not open . Inlet 12 4 3 5 INSTALL WATER LINE CLAMP • Attach the water line clamp (strain relief) (6) from the kit through the clamp (6) at the indent...
...: To ensure a proper ground, the end of the ground wire MUST be used for the house water line (see Water Line Installation Instructions). To make sure the icemaker is not to be secured to the refrigerator cabinet. 4 CONNECT WATER TUBE TO INLET • Squeeze the ends of the hose ... the screw (5) from the kit to the refrigerator. With the clamp directly in line with three of the freezer. Note: After installing the icemaker, do not open . Inlet 12 4 3 5 INSTALL WATER LINE CLAMP • Attach the water line clamp (strain relief) (6) from the kit through the clamp (6) at the indent...