Installation Instructions
Page 1
Installation Instructions Addendum These instructions are needed to install an Icemaker Kit in your Owner's Manual and Installation Instructions. GBS20KBP GBS22HBP GBS22KBP PDS20MBP PDS20SBP PDS22MBP PDS22SBP 197D5736P001 49-60286-3 06-03 JR Icemaker Accessory Kit Addendum for IM4, IM4A and IM6 Icemaker Kits www.GEAppliances.com IMPORTANT: These instructions are to be used to install an icemaker in the models listed below. To be used with your refrigerator. Keep this addendum with an IM4, IM4A or IM6 Icemaker Kit.
Installation Instructions Addendum These instructions are needed to install an Icemaker Kit in your Owner's Manual and Installation Instructions. GBS20KBP GBS22HBP GBS22KBP PDS20MBP PDS20SBP PDS22MBP PDS22SBP 197D5736P001 49-60286-3 06-03 JR Icemaker Accessory Kit Addendum for IM4, IM4A and IM6 Icemaker Kits www.GEAppliances.com IMPORTANT: These instructions are to be used to install an icemaker in the models listed below. To be used with your refrigerator. Keep this addendum with an IM4, IM4A or IM6 Icemaker Kit.
Installation Instructions
Page 2
... from the kit that will be needed to install the icemaker. 1 Icemaker InInsstatrlulacttiioonns 2 Owner's Manual & Installation Instructions 3 Water Valve and Tube Assembly 5 Hex-Head Screw for Water Line Clamp 6 Water Line Clamp (strain relief), for house water line ICEMAKER WARRANTY VERIFICATION Date Installed Dealer 7 Warranty Label 8 Hex-Head Screw, for attaching water valve 9 Phillips Head Screws, for mounting icemaker (2) 10 Water Tube Inlet 11 Icemaker Fill Cup (side-mounted) 12 Hose Clamp 4 Adhesive-Backed Water Tube Fasteners, to secure plastic water tube (4) PARTS REQUIRED THAT...
... from the kit that will be needed to install the icemaker. 1 Icemaker InInsstatrlulacttiioonns 2 Owner's Manual & Installation Instructions 3 Water Valve and Tube Assembly 5 Hex-Head Screw for Water Line Clamp 6 Water Line Clamp (strain relief), for house water line ICEMAKER WARRANTY VERIFICATION Date Installed Dealer 7 Warranty Label 8 Hex-Head Screw, for attaching water valve 9 Phillips Head Screws, for mounting icemaker (2) 10 Water Tube Inlet 11 Icemaker Fill Cup (side-mounted) 12 Hose Clamp 4 Adhesive-Backed Water Tube Fasteners, to secure plastic water tube (4) PARTS REQUIRED THAT...
Installation Instructions
Page 3
... the back of the water tube inlet (10), there is connected to the water supply to the back of the refrigerator. cover 2 INSTALL FILL TUBE • Slide the fill tube shipped with a flat-blade Outlet screwdriver. Firmly press on the inlet to secure it up and out. • Remove the center vertical shelf support (on some models) by pulling it out...
... the back of the water tube inlet (10), there is connected to the water supply to the back of the refrigerator. cover 2 INSTALL FILL TUBE • Slide the fill tube shipped with a flat-blade Outlet screwdriver. Firmly press on the inlet to secure it up and out. • Remove the center vertical shelf support (on some models) by pulling it out...
Installation Instructions
Page 4
... tube has not been pushed out of the back of the icemaker. Installation Instructions 4 INSTALL THE MOUNTING SCREWS • Skip to Step 5 if screws are located in the uppermost position of the mounting slots. • The icemaker is level. • The icemaker power switch is set to O (off). Hook 8 RE-INSTALL THE SHELF SUPPORT, BUCKET, SHELF AND BASKET Replace the center vertical shelf support, ice...
... tube has not been pushed out of the back of the icemaker. Installation Instructions 4 INSTALL THE MOUNTING SCREWS • Skip to Step 5 if screws are located in the uppermost position of the mounting slots. • The icemaker is level. • The icemaker power switch is set to O (off). Hook 8 RE-INSTALL THE SHELF SUPPORT, BUCKET, SHELF AND BASKET Replace the center vertical shelf support, ice...
Installation Instructions
Page 5
... the screws as the access cover must unplug the refrigerator from the kit into the hole in the cabinet leg. Either wire can go on the water valve (3). Cut off excess tubing with ground wire completely onto the water valve. 2 CUT PLASTIC WATER TUBING • Measure 25″ (64 cm) of the refrigerator, remove the screws holding the access cover. Bend the...
... the screws as the access cover must unplug the refrigerator from the kit into the hole in the cabinet leg. Either wire can go on the water valve (3). Cut off excess tubing with ground wire completely onto the water valve. 2 CUT PLASTIC WATER TUBING • Measure 25″ (64 cm) of the refrigerator, remove the screws holding the access cover. Bend the...
Installation Instructions
Page 6
... ground, the end of the ground wire MUST be used for making ice, and will come on. Note: After installing the icemaker, do not open , the green power light on the icemaker will be off. Inlet 12 4 3 5 INSTALL WATER LINE CLAMP • Attach the water line clamp (strain relief) (6) from the kit to I (on) position, power to the home water supply. Installation Instructions 3 ATTACH THE WATER VALVE (cont.) • Clip the end of...
... ground, the end of the ground wire MUST be used for making ice, and will come on. Note: After installing the icemaker, do not open , the green power light on the icemaker will be off. Inlet 12 4 3 5 INSTALL WATER LINE CLAMP • Attach the water line clamp (strain relief) (6) from the kit to I (on) position, power to the home water supply. Installation Instructions 3 ATTACH THE WATER VALVE (cont.) • Clip the end of...