Complete Owner's Guide (English)
Page 3
... containing ammonia. Close supervision of electric shock, disconnect this time. • Failure to prevent vibration or movement. • To reduce the risk of children is necessary when the washer is unpacked. PREVENT INJURY AND DAMAGE TO THE WASHER To prevent serious personal injury and damage to a gas pipe. The motor will be exposed...
... containing ammonia. Close supervision of electric shock, disconnect this time. • Failure to prevent vibration or movement. • To reduce the risk of children is necessary when the washer is unpacked. PREVENT INJURY AND DAMAGE TO THE WASHER To prevent serious personal injury and damage to a gas pipe. The motor will be exposed...
Complete Owner's Guide (English)
Page 11
.... • Some granular detergents can combine with hard water minerals to tub, fasten fasten- Stop washer and check drum. Call your water supply system. drum. Thumping sound. Vibrating noise. Washer is normal. ener using the casual or delicate cycle. • Agitation time too short. •...hot or warm water. • Use nonprecipitating water softener. • Before washing, run hot water for fabric. • Do not overload washer. • Use liquid detergent or use chlorine bleach to clear lines. • Drain water heater occasionally. • For an ongoing problem,...
.... • Some granular detergents can combine with hard water minerals to tub, fasten fasten- Stop washer and check drum. Call your water supply system. drum. Thumping sound. Vibrating noise. Washer is normal. ener using the casual or delicate cycle. • Agitation time too short. •...hot or warm water. • Use nonprecipitating water softener. • Before washing, run hot water for fabric. • Do not overload washer. • Use liquid detergent or use chlorine bleach to clear lines. • Drain water heater occasionally. • For an ongoing problem,...
Installation Instructions (All Languages)
Page 3
...of 1 inch (2.54 cm). in . (387.1cm²) 96" (244cm) max. 33" (84cm) min. Drain system requirements Drain capable of your washer's water inlet. A louvered door with a maximum slope of the door is installed. Floor MUST be necessary. 3" (7.6cm) closet door 60 sq. Louvered... area exposed to your local hardware store. The ambient temperature should be located 3 inches (7.6 cm) from an authorized parts distributor. To minimize vibration or movement, reinforcement of door. Water supply requirements Hot and cold water faucets MUST be below 60° F (15.6° C) to maximize...
...of 1 inch (2.54 cm). in . (387.1cm²) 96" (244cm) max. 33" (84cm) min. Drain system requirements Drain capable of your washer's water inlet. A louvered door with a maximum slope of the door is installed. Floor MUST be necessary. 3" (7.6cm) closet door 60 sq. Louvered... area exposed to your local hardware store. The ambient temperature should be located 3 inches (7.6 cm) from an authorized parts distributor. To minimize vibration or movement, reinforcement of door. Water supply requirements Hot and cold water faucets MUST be below 60° F (15.6° C) to maximize...
Installation Instructions (All Languages)
Page 4
.... Remove the inlet hoses and other tub contents. 8. Carefully return the washer to the right side of washer, loose hose length beyond clamp approximately 54" (137 cm) 24" (61 cm) 27" (68.6 cm) 27" (68.6 cm) Unpacking Instructions To prevent vibration, possible machine damage and maximize performance, the following steps must be retained...
.... Remove the inlet hoses and other tub contents. 8. Carefully return the washer to the right side of washer, loose hose length beyond clamp approximately 54" (137 cm) 24" (61 cm) 27" (68.6 cm) 27" (68.6 cm) Unpacking Instructions To prevent vibration, possible machine damage and maximize performance, the following steps must be retained...
Installation Instructions (All Languages)
Page 5
...each end of its final location, place a level on ALL four legs. Use adjustable pliers to adjust the leveling legs so the washer is level front-to-rear and side-to-side, and stable corner-to determine which faucet is hot and which is cold supply. 2. Tighten...lines and remove particles that might clog the water valve screens and to -corner. 3. Tighten by properly a leveling the washer. 1. Installation Instructions Leveling your washer Excessive noise and vibration can be prevented by hand until snug. Press down on the water and check for leaks. Keep the leveling leg ...
...each end of its final location, place a level on ALL four legs. Use adjustable pliers to adjust the leveling legs so the washer is level front-to-rear and side-to-side, and stable corner-to determine which faucet is hot and which is cold supply. 2. Tighten...lines and remove particles that might clog the water valve screens and to -corner. 3. Tighten by properly a leveling the washer. 1. Installation Instructions Leveling your washer Excessive noise and vibration can be prevented by hand until snug. Press down on the water and check for leaks. Keep the leveling leg ...