Fluke 754-NIST Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 754-NIST manuals!
Problems with Fluke 754-NIST?
Ask a Question
Free Fluke 754-NIST manuals!
Problems with Fluke 754-NIST?
Ask a Question
Popular Fluke 754-NIST Manual Pages
User Manual - Page 5
......61 Linear-Responding Transmitters 61 Square-Root Process Variables 61
Step and Ramp the Output Value 62 Manual Step Use 62 Auto Step Use...62 Ramp the Output 63
Simultaneous Measure/Source 66 Process Instrument ... ...87 Save to and Recall from the Registers 88 Use the Calculator to Set the Source Value 88 Quick Guide to Applications 88 Communication with a PC 101 Maintenance...101
iii
User Manual - Page 6
753/754 Users Manual
Battery Replacement 101 Clean the Product ...101 Calibration Data ...102 In Case of Difficulty 102 Service Center Calibration or Repair 102 User-Replaceable Parts 102 Accessories ...104 Specifications ...106 General Specifications 106 Environmental Specifications 106 Standards and Agency Approval Specifications 106 Detailed Specifications 107 DC mV Measurement 107 DC...
User Manual - Page 13
..., print, or download the latest manual supplement, visit http://us.fluke.com/usen/support/manuals. The Product helps troubleshoot, calibrate, verify, and document work performed on how to Contact Fluke
To contact Fluke, call one of DPCTrack2 can be downloaded at www.fluke.com/process_acc.
1 See the 754 HART Mode Users Guide for instructions on process instruments. For more information...
User Manual - Page 30
...parts of the display are:
• Status Bar: Shows the time and date, and the status of the measure or source function are not shown.
• Secondary Value: Shows the measure or source value in initial engineering units when scaling or custom units are set in Setup mode. 753/754 Users Manual...is "Source Off." all of the display is active-754 only) and low-battery and backlight-on .
18 The...
User Manual - Page 38
...Push s. 2. Push to highlight the language choice. 6. Date and Time
The date and time can also be set since a timestamp is the power-up default. 7. If you choose to not use the date and time display, the calendar...intensity.
In calculator mode, all kept results.
26 753/754 Users Manual
Display Languages
The Product shows information in Setup mode. Push . 5.
User Manual - Page 48
...to go back to exit Setup mode.
8. Push t. 4. Select the necessary thermocouple type using a thermocouple:
1. Push s.
2. 753/754 Users Manual
Temperature Measurement
Thermocouple Use
The Product supports thirteen standard thermocouples, each ...or more for the connector temperature to stabilize after you to choose a setting for MEASURE mode. 3. Attach the thermocouple leads to the correct TC ...
User Manual - Page 56
...set.... Connect the current signal to be setup to show custom units. To do this... jacks.
2. Push .
7. The Product is designed specifically for use with the current shunt:
1. Record the 0%... procedures in native engineering units. The Fluke 700-IV Current Shunt is automatically configured...Custom Units from the list.
6. 753/754 Users Manual
Measure or Source with Custom Units
...
User Manual - Page 71
... for serial communication at 2400, 4800, or 9600 bits per second.
Many models are not supported by leaving drywell source mode and selecting it again.
6. Connect the Product to...The drywell model number will not set to the drywell. Enter the temperature you to check the "High Limit" setting.
59
The drywell driver is within the drywell spec, refer to the drywell manual to select ...
User Manual - Page 92
...14.
Push the Done softkey. 753/754 Users Manual
8. Push More Choices until the ...Transmitter Mode softkey is connected to a current loop that has a power supply, select Simulate Transmitter for example, or ). Set the 0 % and 100 % values for MEASURE/SOURCE mode.
11. To change the Transmitter mode parameters, push Change Setup...
User Manual - Page 114
... Intensity". Service Center Calibration or Repair
Calibration, repairs, or servicing not included in Setup mode. Pressure modules do not use the Product if it if necessary. If the Product will not turn on the sticker should be done only by qualified personnel. User-Replaceable Parts
Table 12 lists the Fluke part number of each userreplaceable part for model or part numbers of...
Calibration Manual - Page 1
Specifications are trademarks of their respective companies. All rights reserved. All product names are subject to change without notice. Printed in USA. 753/754
Documenting Process Calibrator
Calibration Manual
November 2011 © 2011 Fluke Corporation.
Calibration Manual - Page 9
For more information see "Communication with a PC". 753/754 Accessories can be found at www.fluke.com/DPCTrack . Introduction
This manual contains data necessary to Contact Fluke
To contact Fluke, call one of the following telephone numbers: • Technical Support USA: 1-800-44-FLUKE (1-800-443-5853) • Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853) • Canada: 1-800...
Calibration Manual - Page 38
... Power through the setup menu or turn the UUT off. If the Product fails this procedure. Observe the no-load voltage reading on the HART feature.
30
All other transmitters are "supported transmitters". No calibration is necessary for this test, repair is within the range 23.4 V to 28.6 V. 4. 753/754
Calibration Manual
Loop Power To...
Calibration Manual - Page 39
...setup...Fluke Service... repair is...supported or generic: • Poll address (if not 0) • Model... number and Tag ID • PV (Primary Variable) • PVAO (digital representation of the Analog Output) • PV LRV (PV Lower Range Value) • PV URV (PV Upper Range Value) • Softkeys for servicing.
31 Push . 4. Documenting Process Calibrator
HART Mode Verification (754...
Calibration Manual - Page 48
..., Retainer, Isothermal Stopper
Fluke-75x, Stopper, Isothermal
Fluke-753, Mask
Fluke-753, Mask, SI
Fluke-754, Mask
Fluke-754, Mask, SI
Fluke-753, Decal, Case Top
Fluke-754, Decal, Case Top
Fluke-753, Keypad
Fluke-754, Keypad
Input Receptacle Insulator (Black)
Input Receptacle Insulator (Red)
Fluke-75x, Foam, Dust Seal
38 753/754
Calibration Manual
Reference Designator
754
Part Number
MP6, MP7...
Fluke 754-NIST Reviews
Do you have an experience with the Fluke 754-NIST that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!