Fluke 282-U Support and Manuals
Popular Fluke 282-U Manual Pages
Product Manual - Page 10
... the Utility Menu 14-1
Introduction...14-2 Storing and Recalling Set-ups 14-2 Channel Waveform Information 14-2 Warnings and Error messages 14-3 Remote Interface Set-up 14-3 Reference Clock In/Out Setting 14-3 Cursor/Marker Output 14-3 Power On Setting 14-4 System Information 14-4
viii
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 15
... repetition specific reference ...therefore no set -up to two-
Those features associated with any of period or frequency. 281, 282, 284
Users Manual
Introduction
Overview
This manual describes the... wide variety of the Fluke models 281, 282 and 284 single-, two- The instruments provide extensive waveform editing features between the different models when describing the functions associated...
Product Manual - Page 23
... can be set up to 2000 m,
Pollution Degree 2.
Options:
19 inch rack mounting kit. Installation category II
Model 281
Model 282
Model 284
40 VA...Shop for Fluke products online at altitudes up . In this way, complex and versatile inter-channel trigger schemes may be set up to...-20 °C to +60 °C. 281, 282, 284
Users Manual
The signals from the REF IN/OUT socket and the...
Product Manual - Page 32
... follows:
• WAVE SELECT keys call screens from the Utility Menu explains how to appendix B, Warnings and Error Messages. At power-up settings may vary a little with chapter 5, Standard Waveform Operation.
281, 282, 284
Users Manual
Introduction
This section is a general introduction to the organization and principles of the instrument and is intended to...
Product Manual - Page 34
...282, 284
Users Manual...continuous gated triggered
setup...
look, for Fluke products online at the STD (standard waveform) and UTILITY screens. setup... In screens with... appropriate SETUP key; items marked with a double-headed arrow ( ) when selected to scroll all possible settings of ...the lamp lights beside the SETUP key of auto and manual. FILTER SETUP
mode: auto type: 10MHz ...
Product Manual - Page 42
...error... The default set-up can be automatically or manually set to be displayed and for future use it should be saved by pressing the last error...
if selected, phase zero produces a narrow (1 clock) pulse at the start of the associated soft-key; 281, 282, 284
Users Manual... have associated marker bit(s) set -up is required for a beep to restore last setup. Each message has a ...
Product Manual - Page 45
... does not provide a ramp output for Fluke products online at the front panel TRIG IN...over a very wide frequency range (up on setting the marker frequency. In multi-channel instruments ... SETUP screen (accessed by pressing the SWEEP front panel key), or by manually pressing... sweep all 2048 frequency values.
281, 282, 284
Users Manual
Introduction
Principles of Sweep Operation All standard...
Product Manual - Page 46
... done
The maximum sweep range for Fluke products online at once using the rotary control or cursor keys) is selected from this SWEEP SETUP screen.
6 Sweep Operation
Setting Sweep Parameters
Setting Sweep Parameters
Pressing the SWEEP key (or the sweep setup... soft-key on by using the appropriate soft-key. manual...
Note that frequency;
marker... In...
Product Manual - Page 48
... the sweep is set the sweep finishes at the start frequency until it recognizes a trigger, at : www.
.com 1.888.610.7664 Note, however, that in some circumstances, for Fluke products online at ... no wrap is set to on the SWEEP RANGE screen, by a further trigger. Every point of the MAN TRIG key on the SWEEP SETUP screen calls the MANUAL SWEEP FREQ screen:
MANUAL SWEEP FREQ:
1....
Product Manual - Page 101
... Menu
Introduction...14-2 Storing and Recalling Set-ups 14-2 Channel Waveform Information 14-2 Warnings and Error messages 14-3 Remote Interface Set-up 14-3 Reference Clock In/Out Setting 14-3 Cursor/Marker Output 14-3 Power On Setting 14-4 System Information 14-4 Calibration ...14-5 Copying Channel Set-ups 14-5
14-1
MyFlukeStore Shop for Fluke products online at: www.
.com...
Product Manual - Page 120
Status Model
shb0012f.gif
Power on Settings
The following instrument status values are set )
Standard Event Status Enable Register † = 0
Execution Error Register
= 0
Query Error Register
= 0
Parallel Poll Enable Register †
= 0
† Registers marked thus are specific to the GPIB section of limited use in an RS232 environment. nn has been set and a defined state is ...
Product Manual - Page 131
...the revision level of the software installed.
Returns ist local message as ...is .
Query and clear execution error number register. EER? This ...Fluke products online at: www.
.com 1.888.610.7664 Returns the instrument identification. Set the Service Request Enable Register to the value . Returns the value in the Parallel Poll Enable Register in numeric format. 281, 282, 284
Users Manual...
Product Manual - Page 135
... in arbitrary waveform from start address/data / to .
Change the name of the arbitrary waveform . Set hold mode , , or .
16-24
MyFlukeStore Shop for Fluke products online at address in points, of arbitrary waveform to stop address . 281, 282, 284
Users Manual
ARBINSSTD ,, ,
ARBINVERT ,, ARBLEN? ARBLISTCH?
Draw a line in arbitrary waveform from the current...
Product Manual - Page 146
B Appendices
Warning and Error Messages
145 Selected mode is not available when phase lock master or slave 146 Cannot delete arbs while a sequence is running 147 Current set-up requires an arb wfm which does not exist 148 Trig/gate mode and seq step value cause a trigger conflict 149 Seq step value can...
Product Manual - Page 147
...282, 284
Users Manual
Remote Warnings 72 Length is illegal or pattern too long 177 Illegal remote calibration command. 185 Command not available while sweeping. B-4
MyFlukeStore Shop for RS232 170 Length value error... in the ARBDEF(CSV) command
Remote Errors 120 Waveform limit value out of range... mode 165 Cannot set waveform frequency or period for a sequence 166 Cannot set sample frequency or ...
Fluke 282-U Reviews
Do you have an experience with the Fluke 282-U that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!