Edimax ES-5816P Support and Manuals
Get Help and Manuals for this Edimax item
This item is in your list!
View All Support Options Below
Free Edimax ES-5816P manuals!
Problems with Edimax ES-5816P?
Ask a Question
Free Edimax ES-5816P manuals!
Problems with Edimax ES-5816P?
Ask a Question
Popular Edimax ES-5816P Manual Pages
Datasheet - Page 1
... the IT manager's mobility. The ES-5816PE can be sent through a Web Browser. Supports Non-Blocking wire speed The ES-5816P receives and forwards traffic seamlessly with different PoE products such as Access Points, IP cameras or IP phones...It is the best solution where the power outlets are difficult to install or the power outlets are...
Datasheet - Page 2
... • MAC Address based • IP Address based VLAN Setting: • Port Based VLAN • Tag Based VLAN ( 20 entries ) • VLAN ID (Up to 4094K ) QoS: Priority ( Port Based / TOS / Diffserv /DSCP/IPv4/ IPv6) Class of Service Configuration TCP/UDP Port Based Management: Password-protected Access, On /Off...
Manual - Page 2
ID and the password: admin
- 1 -
Web Smart Switch Configure Please follow the steps to configure this switch to your PC's IP to 192.168.2.xx.
Step 2: Set your PC. Step 1: Use a twisted pair cable to 192.168.2.1 Then you will see the login screen. Step 3: Open the web browser (like IE...), and go to connect this Web Smart switch.
Manual - Page 5
Click "Update" to confirm the new change.
will be shown on the screen. Change the IP address: type the new IP address or select DHCP IP configuration.
2. Administrator: System IP Configuration
1. Now, the setting of "System IP Configuration" is finished.
- 4 - "Setting Process OK!!"
Manual - Page 7
Administrator: Load Default Setting
1. Click "Load" to back to the factory default setting. **Note: Recover switch default setting excluding the IP address, User name and Password. Now, the default is loaded.
- 6 -
Manual - Page 13
per port to confirm the setting. Now, the setting of broadcast packets. 3. Set the threshold from 1~63. 2. Port Management: Broadcast Storm Control
1. Click "Update" to define the status of "Broadcast Storm Control" is finished.
- 12 - "Enable Port" - "Threshold" -
Manual - Page 14
... Power: The status of "PoE Configuration" is able to supply power to confirm and finish the setting. Now, the setting of the
port current and minimum output power. 3. Enable: POE of the attached
PD (Powered Device) 4. Click "Update" to the attached
PD (Powered Device) 2. POE class: each POE port will detect the class...
Manual - Page 15
Click "Change VLAN mode" to 2 setting and tag Based VLAN will be disabled automatically. Now, the setting of "VLAN Mode" is enabled, Multi to select the mode. **If the Port Based VLAN function is finished.
- 14 - VLAN Setting: VLAN Mode
There are two VLAN modes : Port Based VLAN and Tagged VLAN.
Manual - Page 16
Click the port numbers: which you want to the original factory setting. Click "LoadDefualt" to back to put them into the
selected VLAN group. 2. VLAN Setting: VLAN Member Setting (Port Based)
You can select a port group. 1. Click "Update" to confirm and finish the setting. 3. Now, the setting of "VLAN Mode" is finished.
- 15 -
Manual - Page 17
choose the port which you don't want to destination ports.
- 16 - "Disable Port" - After this setting, all ports can only connect to use 4. Click "Update" to 2 Setting
This is a special design for easily setting the switch VLAN into "VLAN Per Port". 1. Choose "Destination Port No". 2. Choose "Disable Port" 3. VLAN Setting: Multi to confirm and finish the setting.
Manual - Page 19
... ratio of the transmitting packet for the low priority to confirm and finish the setting.
- 18 - Click "Update" to high priority. 4. "All-High-before-Low" - All packets will be assigned to select. 1. QoS Setting: Priority Mode
There are three Priority Modes to either
Q2(high) piority queue or Q1(low) priority queue. 3. "4 Queue...
Manual - Page 21
...; "802.1p" - Q1 ~ Q4 options are effective for all physical ports. "Physical port" - you can set QoS mode of Service" is the global setting for the
selected physical port only. Click "Update" to configure as the screen shown. 4. "IP TOS/DS Port
Setting" - You can select the port which you want to confirm and finish the...
CE DoC - Page 1
... sole responsibility, that the equipment described below complies with the requirements of Signature: Sep. 4, 2009 Signature:
Printed Name: Title:
Albert Chang Director Edimax Technology Co., Ltd. Equipment : 16-Port 10/100M Web Smart Fast Ethernet Switch Model No. : ES-5816P Report No. : R08102103E-C01
The following European standards for essential requirments have been followed...
Edimax ES-5816P Reviews
Do you have an experience with the Edimax ES-5816P that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Edimax yet.
Earn 750 points for your review!