Edimax ES-5240G V3 Support and Manuals
Get Help and Manuals for this Edimax item
View All Support Options Below
Free Edimax ES-5240G V3 manuals!
Problems with Edimax ES-5240G V3?
Ask a Question
Free Edimax ES-5240G V3 manuals!
Problems with Edimax ES-5240G V3?
Ask a Question
Popular Edimax ES-5240G V3 Manual Pages
User Manual - Page 1
ES-5240G+ 24-Port GbE Web Smart Switch
User's Manual
Version 1.0 / June 2007
User Manual - Page 2
..., the buyer (and not Edimax, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any language or computer...part of Edimax. COPYRIGHT
Copyright© 2007 Edimax. Any software described in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without obligation to the contents hereof and specifically...
User Manual - Page 7
... switch to support two types of each port. Each of Service), VLAN,...Supports Port-based VLAN, IEEE802.1Q Tag VLAN, 24 active VLANs and VLAN ID 1~4094
Port Trunking: Allows one or more links to be aggregated together to incorporate a Web-based management unit that meets IEEE 802.3/u/x/z standards. Introduction
1-1. It is designed to form a Link Aggregation Group by the static setting...
User Manual - Page 11
... 1 to 24 LED
LINK/ACT
Green
Lit when connection with remote device is SFP(LINK/ACT) Green good
Blinks when any traffic is present
Table1-ES-5240G+ LED Indicators table
1-4-2. User Interfaces on 100Mbps speed
10/100/1000Mbps Amber Off when 10Mbps or no link occur
Blinks when any traffic is present...
User Manual - Page 43
... refreshed when a packet with SLA. Bandwidth rating Bandwidth rating is the limitation set another weight to the packet with many ways to implement, and different chips may support different schedule algorithms. Most common schedulers are:
FCFS: First Come First Service. The switch supports by administrator, and it . This function is much to do the...
User Manual - Page 50
... the results may cause the problem of interoperability. Applying LACP in the same Link Aggregation Group must operate in trouble. Increased bandwidth and availability 4. Why 802.3ad (LACP)? LACP is to aggregate the bandwidth of more , no change to be flexible because all 1000Mbps.
Low risk of a specific link, he may:
1. The ports...
User Manual - Page 56
..., password and inactivity timeout. Hardware Version: The hardware version of this device.The switch supports manual IP address setting. Serial Number: The serial number is one of this switch. Without proper settings, network administrator will not be able to manage or view the status of the most important configurations in this switch.
Firmware Version: The firmware version...
User Manual - Page 57
...for the purpose to enable it can configure the IP settings and fill in a network must own its IP address...number and host address. This reduces the total IP number of a network able to support, by the amount of 2 to solve this problem. But unfortunately, the network classes A, B, and C are all too large to... lease time left of this parameter. Up to update. It is shown in this switch.
User Manual - Page 60
...and increased performance but also greatly reduced VLAN management. Then, click button, the settings will be in port-based VLAN. Any packet coming in or outgoing from ... If you are on the port 1, you can support up must be assigned a group name. Fig. 4-4 Port Configuration
4-2-3. Function name:
VLAN Mode Setting
Function description:
The VLAN Mode Selection function includes four...
User Manual - Page 64
... speed, full duplex and the same MAC to build the bandwidth aggregation. Parameter description: Normal:
Set up the ports that do not join any aggregation trunking group. 4-2-5. Function name:
Aggregation Configuration Function description:
Display the current setup of an existed trunking group.
Up to 12 ports can apply your current Ethernet equipments...
User Manual - Page 71
... the combination of the authentication status and the port status versus the status of authentication supported in 802.1x port setting. The following table is the type of port mode, set in 802.1x Port mode, port control state, set to this port can access the network resource through this port.
802.1x Port...
User Manual - Page 72
... controlled port is set to be used to hold in ...supported, Force Unauthorized, Force Authorized and Auto. Re-authenticate: Specify if subscriber has to periodically re-enter his or her username and password... to stay connected to hold in at once.
66 It is forced to the port. y Force Authorized: The controlled port is a string with RADIUS server for the authentication service...
User Manual - Page 76
... Mirror Port respectively. Fig. 4-20 Mirror ports configuration
70 Mirror Port:
Use the drop-down menu to Port C for being monitored. Parameter description: Source Port:
Set up the port for monitoring. 4-2-10. The traffic passed by Port A and Port B will be copied to select a mirror port.
Mirror Configuration Function name:
Mirror...
User Manual - Page 110
... without notice.
104 Ports trunk connections allowed
Supports by-port Egress/Ingress rate control
Referred as Class of Service (QoS)
Auto-negotiation support on 10/100Base-TX ports, Web browser can set transmission speed (10/100Mbps) and operation mode (Full/Half duplex) on HTTP Server
Note: Any specification is subject to 24 active VLANs in...
User Manual - Page 111
... 5205 }
switch
OBJECT IDENTIFIER ::= { privatetech 2 }
ES-5240G+ProductId OBJECT IDENTIFIER ::= { switch 7 }
ES-5240G+Produces OBJECT IDENTIFIER ::= { ES-5240G+ProductId 1 }
ES-5240G+IllegalLogin TRAP-TYPE ENTERPRISE ES-5240G+ProductId DESCRIPTION "Send this trap when the number of the Tx bad packet over the Rx Error Threshold. Appendix B MIB Specifications
MIB II Enterprise MIB brief...
Edimax ES-5240G V3 Reviews
We have not received any reviews for Edimax yet.