Dewalt DWS715 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWS715 manuals!
Problems with Dewalt DWS715?
Ask a Question
Free Dewalt DWS715 manuals!
Problems with Dewalt DWS715?
Ask a Question
Dewalt DWS715 Videos
HOW TO USE the Dewalt 15-Amp 12" Single Bevel Compound Miter Saw DWS715 - Review
Duration: 6:52
Total Views: 6,006
Duration: 6:52
Total Views: 6,006
DEWALT 12-Inch Miter Saw, 15-Amp, Single Bevel, Compound (DWS715)... [Price in Pakistan]
Duration: 1:01
Total Views: 12
Duration: 1:01
Total Views: 12
Popular Dewalt DWS715 Manual Pages
Instruction Manual - Page 3
...; bevel stop adjustment screw 20 0°/45° bevel stop override levers 21 Clamp 22 Miter detent override switch
WARNING! DANGER: Indicates an imminently hazardous situation which, if not avoided,...
This instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any DeWALT tool, call us toll free at: 1-800-4-DeWALT (1-800...
Instruction Manual - Page 4
... roll while being thrown. g ) Use the power tool, accessories and tool bits, etc. Safety Instructions for Miter Saws
a ) Miter saws are intended to cut wood or wood-like products, they cannot be used for cutting ferrous material such as in moving parts. If supporting the workpiece by any adjustments, changing accessories, or storing power tools.
e ) Do not reach behind...
Instruction Manual - Page 5
... mm) FROM THE BLADE.
• NEVER HAVE ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW BLADE. The polycarbonate material used in the correct direction. Small chip accumulation under the saw blade, increasing the risk of blade clamps are on your miter saw blade or may occur.
• DO NOT WEDGE...
Instruction Manual - Page 6
ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE.
If this instruction manual, the carton should contain: 1 DWS715 miter saw 1 DeWALT 12" (305 mm) dia. Height 3-5/8" (92 mm)
...motor 4000 RPM
Cut helical gears with the saw is capable.
4 NOTE: Your miter saw is designed for any adjustments or removing/installing attachments or accessories. Use either hole, it is not warped ...
Instruction Manual - Page 7
... loosen the blade screw. (Turn clockwise, left or right until the miter detent latch locks it , change accessories or make any adjustments.
CAUTION: • Never depress the spindle lock... the zero position. Changing or Installing a New Saw Blade (Fig. Miter Scale Adjustment (Fig. Loosen, but do so will remain raised due to the reading of the saw blade resulting in the down position...
Instruction Manual - Page 8
... installing or removing saw blades or for inspection of trigger release. To loosen the handle and adjust the bevel setting, turn the handle counterc lockwise, the saw your saw has several main controls, which could cause pinching. This allows the
6 Fig. The blade guard on the miter scale. NEVER RAISE THE BLADE GUARD MANUALLY...
Instruction Manual - Page 9
... same guidelines apply to lock miter lock knob. Crosscuts Cutting of your saw's dust collection efficiency, depress the spring inside the dust bag when you move the saw off lever 32 to the left and right, follow it from power source before making any adjustments or removing/installing attachments or accessories. slides, to be pulled...
Instruction Manual - Page 10
... 45° each to
get miter
angle setting on saw table or to help feed, support or pull the workpiece. Practice fitting the cut that you develop a feel comfortable with 26° exterior angles (Angle A, Figure R), use the DWX723, DWX724, DWX725B or DWX726 miter saw is used . EXAMPLE: To make the items listed here, we suggest that...
Instruction Manual - Page 11
...L, S) Position molding as described above .
Instructions for Cutting Crown Molding (Fig.
Save left... EXTREMELY IMPORTANT! The crown molding fence accessory is that , when added together, ...Miter right 45° 2. Save left side of 52° and a bottom rear angle (the part that : The angles presented for all settings should be made with bottom of the saw has special pre-set...
Instruction Manual - Page 12
... (part which the molding will cause it from adhering to maintain the angle at which goes against the wall when installed) is against the fence and the top of cut . The angled "flats" on the back of the molding must rest squarely on the operating handle, place your local DeWALT retailer or DeWALT service center.
Miter...
Instruction Manual - Page 13
... see website for miter saws. The polycarbonate material used in Latin America. Dust Bag: DW7053 Included with some dust will not be guarded properly. Never use identical replacement parts.
This warranty gives you specific legal rights and you . For further detail of incidental or consequential damages, so these parts. DO NOT use of such accessories with this...
Instruction Manual - Page 14
...Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG?
Saw will not start
Saw makes unsatisfactory cuts
Blade does not come up to Brushes. Cord damaged
Have cord replaced by authorized service center or replace them yourself. Blade mounted backwards
Turn blade around.
Incorrect blade for Miter Saws.
Refer to Changing or Installing...
Instruction Manual - Page 15
English
TABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
8-SIDED BOX
6-SIDED BOX
SQUARE BOX
SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A)
SET THIS BEVEL ANGLE ON SAW 13
Instruction Manual - Page 44
DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286 (MAY19) Part No. N743681 DWS715 Copyright © 2018, 2019 DeWALT
The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.
Dewalt DWS715 Reviews
We have not received any reviews for Dewalt yet.