Dewalt DWS520SKH Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWS520SKH manuals!
Problems with Dewalt DWS520SKH?
Ask a Question
Free Dewalt DWS520SKH manuals!
Problems with Dewalt DWS520SKH?
Ask a Question
Popular Dewalt DWS520SKH Manual Pages
Instruction Manual - Page 3
... or moving parts. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE ... abuse the cord.
WARNING: To reduce the risk of injury, read the manual and pay attention to follow the warnings and instructions may result in the presence of flammable liquids, gases or dust. e) When...
Instruction Manual - Page 4
...repaired before use the power tool if the switch does not turn it was designed. A moment of the power tool for your power tool serviced...control. Power tools are caused by a qualified repair person using only identical replacement parts. f) Keep cutting tools sharp and clean....of dust extraction and collection facilities, ensure these instructions to power source and/ or battery pack, ...
Instruction Manual - Page 5
...of the workpiece toward the operator. - d) Support large panels to the thickness of blade pinching and...Never use a rip fence or straight edge guide.
The guard cannot protect you to a ...hold the saw will also make exposed metal parts of the power tool "live " wire... toward the operator. -
English
ADDITIONAL SPECIFIC SAFETY RULES
Safety Instructions for All Saws
a) DANGER: Keep hands...
Instruction Manual - Page 6
...Model DWS520 does not require removal of the blade. Even a light interference can create kickback. Additional Safety Instructions for 6000 RPM operation (or higher).
4 Support must be serviced before each use the riving knife except when plunge cutting. Unsharpened or improperly set... may be replaced after switch ...Exposure to damaged parts, gummy deposits,... this instruction manual. Guard...
Instruction Manual - Page 9
... can cause injury. WARNING: To reduce the risk of injury, turn unit off and
I
disconnect it from power source before installing and removing
accessories, before adjusting or when making repairs. ADJUSTMENTS AND SET-UP
WARNING: To reduce the risk of serious personal injury, do not use this saw to cut wood.
FIG. 1
MA...
Instruction Manual - Page 10
...adjustment screw (R) with the track attached: 0-2-1/8" (0-55 mm).
1. with an hex wrench (Z)
and set at 0-2-5/16" (0-59 mm) without track attached;
OPERATION
WARNING: To reduce the risk of the... before installing and removing
8 Tighten the riving knife screw (R).
English
2. Set the bevel angle by about 1/8" (3 mm). Cutting Depth Adjustment (Fig. 4)
The cutting depth can be set the ...
Instruction Manual - Page 11
...area to top position. 11.
DON'T support board or panel away from power source before installing and removing accessories, before adjusting or when making repairs. WARNING: When operating the saw back ...condition. To avoid kickback, DO support board or panel NEAR the cut . NOTE: The blade (K) is engaged. Switching On and Off (Fig. 1)
Pull the On/off . Replace the outer flange (O) and blade...
Instruction Manual - Page 12
Cutting
DANGER: Risk of the saw. Keep your nearest authorized DEWALT service center for the proper way to be cut or pushed forward into kerf ... saw from the workpiece while the blade is important to support the work . down.
DO NOT force the tool. Use caution when sawing material from the cutting area to Figure 7 for repair. Keep the cord away from below. Refer to prevent ...
Instruction Manual - Page 13
... 1, 8) WARNING: ALWAYS use a track, fence or straight edge guide when ripping. Do not operate tools rated AC only on which the.... Place the machine with the front part of material, and knotty or damp ... . WARNING: To avoid kickbacks, the following instructions MUST
be careful to force it working without ... the switch and allow the blade to set cutting depth and push it forward into...
Instruction Manual - Page 14
... during the plunge cut will be on a large table, bench, or floor, several pieces of supporting the workpiece. This operation is called a compound cut , turn the antikickback knob (U) counterclockwise to ...the same manner as crosscuts and rip cuts, but set cutting depth and push forward in the center.
If the workpiece is supported on the left. BEVEL CUTTING Make your bevel cuts...
Instruction Manual - Page 15
...the blade stalls and the motor reaction drives the unit backward. C.
E. IMPROPER DEPTH OF CUT SETTING ON SAW
To make the most efficient cut , the teeth at the outer ends only can... occur.
7. See the section titled Cutting Depth Adjustment.
3. Pushing harder to cut through material supported at the back edge of the blade can cause kickback. Pressure treated lumber (material treated with...
Instruction Manual - Page 16
...wood. 3. Only operate saw when proper saw system instruction before the first use a clean, sharp ... 0.79" (20 mm) diameter bore.
The guide clearance of kickback. Hold the track adjuster in pinching...: VISUALLY EXAMINE CARBIDE BLADES BEFORE USE. REPLACE IF DAMAGED. Securing the workpiece with clamps... saw and personal injury may result. Set the speed of the track.
14
...
Instruction Manual - Page 17
... outlet (I). The edge of the anti-splinter strip now corresponds exactly to the set cutting depth and cut between 1750 and 4000/min using clean, dry compressed air...sawdust toward yourself or others. To avoid injury from power source before installing and removing accessories, before adjusting or when making repairs.
MAINTENANCE
WARNING: To reduce the risk of material and speed range....
Instruction Manual - Page 18
... with electric brakes, which may seriously damage plastic parts. WARNING: DO NOT USE WATER FEED ATTACHMENTS WITH THIS SAW. Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center or other than those offered by DEWALT, have...
Instruction Manual - Page 19
.... LATIN AMERICA: This warranty does not apply to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for a full refund -
English
warranty gives you specific legal rights and you can return it within 90 days from the date of E.
Dewalt DWS520SKH Reviews
We have not received any reviews for Dewalt yet.