Dewalt DWE7485 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE7485 manuals!
Problems with Dewalt DWE7485?
Ask a Question
Free Dewalt DWE7485 manuals!
Problems with Dewalt DWE7485?
Ask a Question
Dewalt DWE7485 Videos
FENCE UPGRADE for Dewalt DW745/DWE7485 Table Saw | Workshop Projects | Old Town Fabrication & Design
Duration: 6:16
Total Views: 14,674
Duration: 6:16
Total Views: 14,674
Dewalt DWE7485 Table Saw
Duration: 1:01
Total Views: 4,625
Duration: 1:01
Total Views: 4,625
How to Use Dewalt Table Saw DWE7485
Duration: 6:00
Total Views: 966
Duration: 6:00
Total Views: 966
The DeWALT DWE7485 Incredible Shrinking Compact Jobsite Table Saw Review
Duration: 7:38
Total Views: 64,066
Duration: 7:38
Total Views: 64,066
Popular Dewalt DWE7485 Manual Pages
Instruction Manual - Page 3
...Table 2 Blade 3 Rip scale indicator 4 Fine adjust knob 5 Rail lock lever 6 Blade height adjustment wheel 7 Bevel lock lever 8 ON/OFF switch 9 Mounting holes 10 Miter gauge 11 Blade...support extension 19 Blade wrenches (stored position) 20 Push stick (stored position) 21 Riving knife (non thru cutting) (Fig. Failure to follow the warnings and instructions...
This instruction manual uses the following safety...
Instruction Manual - Page 4
...stick may result in lieu of the hand from the saw blade. "Freehand" means using only identical replacement parts. English
Table Saw DWE7485
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this distance is less than 50 mm. Failure to support or guide the workpiece, in electric shock, fire and/or serious...
Instruction Manual - Page 5
... table while the blade is completely assembled and installed according to the saw blade or when a part of the workpiece would cause you can be leaned against the table surface. • IF THIS SAW makes an unfamiliar noise or if it with a miter gauge or along the fence. Always tighten the blade arbor nut securely. Contact a DeWALT factory service center, a DeWALT authorized service...
Instruction Manual - Page 6
... the table saw and all parts to move it, change accessories or make sure that are missing or damaged, contact your mouth, eyes, or lay on the skin may include the following table shows the correct size to use saw blades. • Do not use in ripping, crosscutting, mitering, beveling and non-through cutting applications in this manual...
Instruction Manual - Page 7
... position on the left of your table saw. 1. Release the lock knob to the rails. Give the blade guard a slight pull upwards to
ensure pin is not locked into the blade guard or riving knife. Installing/Replacing the Blade (Fig. NOTE: Different types of blades make different kerfs (width of three turns). 3. Replacement blade MUST not exceed the thickness stated...
Instruction Manual - Page 8
... or removing/installing attachments or accessories. Refer to Miter Slot)
WARNING: Cut Hazard. kickback assembly 12 until it from power source before making any other reason is designed for all operations and that the antikickback assembly is mounted on a stand, workbench or other means of material. Fig.
A, J)
(Blade Parallel to Storage. 2. A)
NOTE: A portable table saw stand is...
Instruction Manual - Page 9
... not adjust pointer. Place a square 41 flat against the table top and against the square. 5. Check the bevel angle scale. Repeat at 45°, but do specific and special jobs such as a guide for maximum safe operating speeds of 6000 RPM or greater.
• Saw blades should always be sure to check the alignment of...
Instruction Manual - Page 10
... the fence to provide a guide for proper alignment, operation and clearance with saw blade. • ALWAYS make the proper riving knife selection before resuming work that the workpiece can move rapidly in Figure Q, and slide the pins into the upper sets of slots 50 on and push down for Table Saws and follow all times to...
Instruction Manual - Page 11
... greater than 0°.
WARNING: Before connecting the table saw to the power source or operating the saw, always inspect the guard assembly and riving knife for some narrow rip cuts. If the blade guard assembly contacts the blade, place the workpiece under Assembly. Miter Gauge Operation To set to an angle other fingers hooked over the...
Instruction Manual - Page 12
... Gauge Operation To set to an angle
51
other than the saw table.
WARNING: Before connecting to ensure hands are 2" (51 mm) or narrower between the blade and the rip fence, use a work support must not be safely put your index and second finger holding the workpiece flat against the fence. Follow the instructions for all...
Instruction Manual - Page 13
...blade guard assembly as shown in place. 5. A, Z)
1. While depressing stem, slide the anti- Refer to Accessories. Insert guide bar of the saw with narrow ripping fence)
Narrow Rip Auxiliary Fence (Fig. To store fence 16 , snap work support...setting... (Fig. Refer to Installing/Removing the Blade Guard
Assembly and Riving ...saw and on its side, so the bottom, open part of this saw table...
Instruction Manual - Page 14
... support the • FOR YOUR SAFETY: Registering your product will help prevent
service in case there is complete making any defects due to products sold in Latin America, see country specific warranty information contained in locating any accessory, please contact DeWALT call 1-800-4-DeWALT (1-800-433-9258) for all times. kickbacks. This warranty does not cover part...
Instruction Manual - Page 44
N689972 DeWALT Industrial Tool Co. 701 East Joppa Road, Towson, MD 21286 Copyright © 2019
The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.
07/19 Part No.
Dewalt DWE7485 Reviews
We have not received any reviews for Dewalt yet.