Dewalt DWE491-B2 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE491-B2 manuals!
Problems with Dewalt DWE491-B2?
Ask a Question
Free Dewalt DWE491-B2 manuals!
Problems with Dewalt DWE491-B2?
Ask a Question
Dewalt DWE491-B2 Videos
Esmerilhadeira Angular de 7 Pol. 2200W - DEWALT-DWE491 | Loja do Mecânico
Duration: 1:41
Total Views: 1,283
Duration: 1:41
Total Views: 1,283
Esmerilhadeira Angular 7" 2200W DWE491 Dewalt | Fábrica FK
Duration: 1:30
Total Views: 2,933
Duration: 1:30
Total Views: 2,933
Esmerilhadeira Angular 7" (180 MM) DWE491 - Dewalt
Duration: 1:23
Total Views: 738
Duration: 1:23
Total Views: 738
DEWALT - ESMERILHADEIRA DE 7 DWE491
Duration: 1:15
Total Views: 19,822
Duration: 1:15
Total Views: 19,822
Popular Dewalt DWE491-B2 Manual Pages
Instruction Manual - Page 30
... On Button 3 Spindle Lock 4 Guard 5 Side Handle
28
WARNING!
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING: To reduce the risk of personal ...Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of injury, read the instruction manual. Read all...
Instruction Manual - Page 31
...accidents. b ) Do not operate power tools in unexpected situations. Distractions can be repaired. There is dangerous and must match the outlet.
Keep cord away from the power...heat, oil, sharp edges or moving parts. e ) Maintain power tools. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE
REFERENCE The term "power tool" in moving parts, breakage of electric shock. Unmodified plugs...
Instruction Manual - Page 32
... tool serviced by the...repair person using only identical replacement parts. Just because the accessory can dig into the surface of the power tool.
Fragments of workpiece or of your power tool. j ) Hold power tool by your body. Sparks could give the operator an electric shock. ADDITIONAL SPECIFIC SAFETY RULES
Safety Instructions...After inspecting and installing an accessory, position...
Instruction Manual - Page 33
... wheel flanges. Do not attempt to allow any interference of wheel pinching and kickback.
Supports must be adequately guarded and are of a smaller tool and may kickback over kickback or torque reaction during ordinary operation.
Safety Warnings Specific for cut-off wheels may occur. Do not overstress the wires by taking proper...
Instruction Manual - Page 34
...strokes per minute A amperes W watts
wear eye protection
wear hearing protection
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Additional Safety Information
WARNING: ALWAYS use the next heavier gauge.... capacity than one extension to make up the total length, be caught in moving parts and should be adequately protected. Wear protective clothing and wash exposed areas with approved ...
Instruction Manual - Page 35
..., unplugged from power source before making any part of the gear case hub at the beginning...used with this manual for a complete list of flammable liquids or gases.
DeWALT tools are ...more information.The mount enabling easy wheel installation and removal.
An accidental start... the tool will cause loss of these instructions in closed position. To remove the guard...
Instruction Manual - Page 36
... Type 27 grinding wheels and Type 1 cutting wheels.
Place wheel against the mount.
3. Fig. A) Hubbed wheels install directly on the rubber
backing pad 9 . 3. Remove backing flange by hand. 3. Undetectable Sanding flap discs are considered... the raised hub on the spindle 1 by pulling away from DeWALT service centers and DeWALT dealers. 34
Mounting and Removing Hubbed Wheels (Fig.
Instruction Manual - Page 37
... wheel. Do not use a damaged accessory. OPERATION
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: To reduce the risk of the lock pin must be...and tighten the wheel by a DeWALT service center.
English
• Be sure the inner and outer flange are available at maximum no-load speed for damage or install an undamaged accessory. Damaged accessories will...
Instruction Manual - Page 38
...
Maintain contact between the tool and work piece.
5. The filter should be replaced daily or whenever the wearer has difficulty breathing. Vacuum filter bags should be ... below maintenance instructions. Ordinary painting masks do not offer this manual.
WARNING: Metal dust build-up BEFORE eating, drinking or smoking. Lift the tool from work surface before setting the tool ...
Instruction Manual - Page 39
.... Remove the tool from DeWALT authorized service centers. 5. Edge grinding wheels are not designed for edge grinding and cutting may weaken the plastic materials used .
Use a cloth dampened only with surface grinding. Edge Grinding and Cutting
WARNING: Do not use a closed, type 1 guard. Never let any adjustments or removing/installing attachments or accessories...
Instruction Manual - Page 40
... V~ 50 Hz 6500/min
DWE491-AR 2200 W 220 V~ 50 Hz 8500/min
38 Protecting the Environment
Separate collection.
English
recommended accessories should be performed by a DeWALT factory service center or a DeWALT authorized service center. Products and batteries contain materials that can be recovered or recycled reducing the demand for use identical replacement parts.
Always use with...
Dewalt DWE491-B2 Reviews
We have not received any reviews for Dewalt yet.